Patterns?
#11
I don't even bother looking at the measurements they are supposed to be anymore. One of the best books I own is triangle free quilts. The reason being is she has you cut for your blocks out those together and then has you remeasure to see what size blocks you have then cut for the next part and so on. I hardly ever match up with the perfectness of the pros and your looking at a picture there is no proof even there sample was perfect to the measurements in the pattern. I'm not picky on a particular size though so I always square up my blocks and go from there and all my quilts have turned out so nice and I have always been happy!
#13
Super Member
Join Date: Aug 2010
Location: Northern California, Sonoma Co.
Posts: 2,814
I learned the hard way that following the edge of my quarter-inch foot does not guarantee a quarter-inch seam -- I actually need the fabric to run just under the edge, not at the edge. It's very frustrating, and I have had blocks turn out too small and been unable to send them to swaps.
I feel for you!
I feel for you!
#14
Super Member
Join Date: May 2010
Location: Windham, Maine
Posts: 1,251
The best way I have found to make sure of your seam allowances - and I do believe this is the culprit in most cases - is to cut 3 strips 1 1/2" wide. Sew the strips together long ways. At the ironing board - set the seams and then press the seam allowances out. Measure the center strip. Is it 1" wide??? Too narrow? Your seam is too big. Too wide? Your seam is too small. Once you get it RIGHT - put masking tape on your machine in the right place! It takes only a little bit of time and saves so much frustration.
#15
Super Member
Join Date: Aug 2007
Location: Clay Springs AZ
Posts: 3,229
I have to use a scant on all my blocks. Even using a quarter inch foot my blocks never come out full size.
It dosnt matter for your own quilts but when making blocks with others they need to be the right size.
So now I set my machine with smaller seams all the time even though it has a quarter inch setting.
Even using different machines I still have to use scant.
It is not my cutting as I measure to make sure the pieces are the right size.
It dosnt matter for your own quilts but when making blocks with others they need to be the right size.
So now I set my machine with smaller seams all the time even though it has a quarter inch setting.
Even using different machines I still have to use scant.
It is not my cutting as I measure to make sure the pieces are the right size.
#16
Super Member
Thread Starter
Join Date: Dec 2009
Posts: 3,422
The best way I have found to make sure of your seam allowances - and I do believe this is the culprit in most cases - is to cut 3 strips 1 1/2" wide. Sew the strips together long ways. At the ironing board - set the seams and then press the seam allowances out. Measure the center strip. Is it 1" wide??? Too narrow? Your seam is too big. Too wide? Your seam is too small. Once you get it RIGHT - put masking tape on your machine in the right place! It takes only a little bit of time and saves so much frustration.
#17
Even books have mistakes in them. Im making Sylvias Bridal Sampler. Before I started I went to the web site and sure enough there it was, a list of several of the patterns and their mistakes. Was glad I checked. I used to make samples for our LQS, I could'nt believe all the patterns that had mistakes in them.
You should come join us in the Block of the Week that Jennifer Chiaverini sponsors. It's a lot of fun! Just visit the SBS website at www.sylviasbridalsampler.com.
Lynda
#20
Power Poster
Join Date: May 2008
Location: MN
Posts: 24,659
Lots of good suggestions -
Double check your pattern pieces - if you used templates - make sure they are the correct size.
I had bought some plastic templates with the pattern shapes printed on them. Turned out that the "square" was 4-1/2 x 4-5/8 - which explained why my pieces weren't going together very well. I didn't figure that out until the quilt was done, though!!! Hey - I bought it - it should have been perfect, right?
Now I trust myself a lot more than I did then.
Learn and live!
Double check your pattern pieces - if you used templates - make sure they are the correct size.
I had bought some plastic templates with the pattern shapes printed on them. Turned out that the "square" was 4-1/2 x 4-5/8 - which explained why my pieces weren't going together very well. I didn't figure that out until the quilt was done, though!!! Hey - I bought it - it should have been perfect, right?
Now I trust myself a lot more than I did then.
Learn and live!
Thread
Thread Starter
Forum
Replies
Last Post
craftybear
Links and Resources
12
08-30-2011 07:20 PM
craftybear
Links and Resources
3
07-18-2011 03:08 AM