Quiltingboard Forums

Quiltingboard Forums (https://www.quiltingboard.com/)
-   Main (https://www.quiltingboard.com/main-f1/)
-   -   Diagonal Joins (https://www.quiltingboard.com/main-f1/diagonal-joins-t281576.html)

Dolphyngyrl 08-23-2016 08:12 PM


Originally Posted by dunster (Post 7634649)
I just eyeball it and sew away. Any discontinuity seems to disappear after the binding is sewn down.

Me too dunster, better done than perfect

Jeanne S 08-23-2016 08:22 PM


Originally Posted by Tartan (Post 7634598)
I usually cross my strips with a little extra on each end. That lets me sew from V valley to valley for a nice join. I also have a piece of painters tape on the bed of my machine with a straight line drawn on with a sharpie. If I keep the little V valley on the line opposite from the needle, I can sew a straight join without marking.

This is my method too, including the blue tape!!!!

ManiacQuilter2 08-24-2016 04:13 AM

I overlap the ends too and sew diagonally. like Tartan. Another trick when doing corners on binding is to make sure that the folds lay in opposite directions.

PaperPrincess 08-24-2016 04:36 AM

The two strips have to be exactly perpendicular. Draw the diagonal line. Must be 45 degrees. then use the markings on your cutting mat to align the strips perfectly. Pin, then sew. wen you sew, the seam has to start in the corner where the 2 strips meet, and end where they meet. I also had problems until started using my mat for alignment

LavenderBlue 08-24-2016 05:30 AM

Diagonally joining the binding ends is my least favorite part of the entire quilting process!

letawellman 08-24-2016 07:39 AM


Originally Posted by dunster (Post 7634649)
I just eyeball it and sew away. Any discontinuity seems to disappear after the binding is sewn down.

Me too. I might fold the corner down to ensure a 90* angle (instead of something that looks like lightning), but once it's in place, you never see the misalignment.

rryder 08-24-2016 08:33 AM

I overlap them just a bit, pin on each side of the diagonal (place them parallel to the diagonal and far enough from it so they won't get sewn over), then lay an index card along the diagonal and mark it. The index card is flexible enough that it won't wobble when you lay it over the pins like a ruler will, but the edge is sturdy enough that you can mark a nice straight line with it. Then sew along the mark, leaving the pins in place until done. Works well for me.

Sometimes there is a little bit of discrepancy but as long as it's smaller than your seam allowance it won't show.

Rob
<object type="cosymantecnisbfw" cotype="cs" id="SILOBFWOBJECTID" style="width: 0px; height: 0px; display: block;"></object>

geevee 08-24-2016 02:31 PM

It's comforting to know I'm not the only one who finds it not as easy as the tutorials make it seem to be, and also that a slight imperfection in the join won't mess up the finished binding, I was afraid it would bunch or not lay flat or do some other strange thing that would make me have to rip it all out. Thanks everyone for all your thoughts and tips, I feel much better now. :)

Aurora 08-25-2016 02:44 AM

Gee, I never have a problem with this. I don't think about it much, I just do it. For me, if I think about how to do something, I have a much more difficult time doing it.

LGJARN52 08-25-2016 03:40 AM

Some days I get it right the first time....others I'm off just a bit. I'm not a perfectionist and never want to be....would rather walk on the wild side like Dunster.


All times are GMT -8. The time now is 03:07 AM.