Go Back  Quiltingboard Forums >
  • Main
  • Help with machine free motion quilting >
  • Help with machine free motion quilting

  • Help with machine free motion quilting

    Thread Tools
     
    Old 08-27-2009, 07:45 PM
      #1  
    Super Member
    Thread Starter
     
    SherriB's Avatar
     
    Join Date: Aug 2009
    Location: Quilting somewhere......
    Posts: 2,591
    Default

    I am fairly new at quilting. I have made a few quilts and have stitched them in the ditch.

    I just finished my granddaughter a quilt and did some free motion quilting on it. I did kind of okay on the front, my stitches are FAR from even. My problem was the tension on the back. I dropped the feed dogs and used the darning foot sold to me by the Janome dealer. I tried adjusting the tension a little but it seemed like it made the problem worse.

    I have a Janome HT 2008. I tried reading the manual but no luck. Any suggestions will be greatly appreciated!!
    SherriB is offline  
    Old 08-27-2009, 07:55 PM
      #2  
    Super Member
     
    mgshaw's Avatar
     
    Join Date: Jul 2007
    Location: Oklahoma
    Posts: 3,075
    Default

    I am just learning FMQ too and I had to crank the tension all the way up to 5 and even up to 8 depending on the thread. Just make a practice sandwich and stitch a little bit, check it, adjust, stitch some more, check it, adjust some more if needed etc, etc...... until you find your weet spot :D
    mgshaw is offline  
    Old 08-27-2009, 08:18 PM
      #3  
    Super Member
     
    amandasgramma's Avatar
     
    Join Date: May 2009
    Location: La Pine Oregon, USA
    Posts: 5,907
    Default

    mgshaw is correct. That's what I learned in class, too.
    amandasgramma is offline  
    Old 08-27-2009, 08:25 PM
      #4  
    Super Member
    Thread Starter
     
    SherriB's Avatar
     
    Join Date: Aug 2009
    Location: Quilting somewhere......
    Posts: 2,591
    Default

    Thank you both! I am going to try cranking up the tension and practice on some scrap quilt sandwiches tomorrow.
    SherriB is offline  
    Old 08-27-2009, 08:32 PM
      #5  
    Senior Member
     
    Lisa T's Avatar
     
    Join Date: Jan 2009
    Location: Menominee, Michigan
    Posts: 914
    Default

    I attempted my first FMQ-ing yesterday. I had to turn my tension all the way up to 8 to get it to work right.
    Lisa T is offline  
    Old 08-28-2009, 04:37 AM
      #6  
    Senior Member
     
    Roben's Avatar
     
    Join Date: Mar 2008
    Location: SW IA
    Posts: 900
    Default

    Another thing to keep in mind is speed when stitching curves. If I go around a curve to fast, I end up with 'eyelashes' on the back, where the bobbin thread is almost straight and the top thread pulls through to the back. It looks like it would be a tension problem, but it's actually a speed problem :?
    Roben is offline  
    Old 08-28-2009, 04:43 AM
      #7  
    Super Member
     
    justwannaquilt's Avatar
     
    Join Date: Aug 2009
    Location: Union, Missouri
    Posts: 1,542
    Default

    I was going to type <almost> exactly what Roben did, sometimes if you are moving to fast and pulling your fabric around to fast it can look like you have a tension problem but really you are just moving the fabric around to fast. This will also cause needles to break and thread to snap!! Ask me how I know!
    justwannaquilt is offline  
    Old 08-28-2009, 06:13 AM
      #8  
    Super Member
     
    Join Date: Aug 2007
    Location: South Puget Sound, Wa. State
    Posts: 2,462
    Default

    Thanks for the info!!!
    I never thought I could be going "too fast", now I know why I have eyelashes!!! :oops:
    Kirsten
    ScubaK is offline  
    Old 08-28-2009, 07:30 AM
      #9  
    Junior Member
     
    Lainee's Avatar
     
    Join Date: Mar 2009
    Location: Ellijay, Georgia
    Posts: 155
    Default

    Hi...yes, don't change quilting directions to quickly. It is also helpful to use something to have a better grip on the sandwich like finger cots, rubber finger tips, gardening gloves, a halo or like device. Also, make sure that the surface that the sandwich is sliding on is as slippery as possible...I bought the teflon slidder sheet. Some have used plastic sheeting (with hole for needle) and some have even suggested waxing the surface of your machine bed.

    Practice, practice, practice...it's like skiing or riding a bike...keep trying and before you realize it things have come together and you're doing it.

    And don't be too critical of yourself...I've seen stitching on quilts in quilt shops that made me feel much better about my stitches!
    Lainee is offline  
    Old 08-28-2009, 07:50 AM
      #10  
    Power Poster
     
    nativetexan's Avatar
     
    Join Date: Feb 2009
    Location: home again, after 27 yrs!
    Posts: 19,388
    Default

    one thing, did you bring the bobbin thread up to the top before doing your quilting? You need to do that, hold the threads and take a few tiny stitches (barely moving the quilt) and then trim the threads when you can.
    that should help. a clean machine helps a lot too.
    zero stitch length is good but not necessary. the movement of the quilt determines the length but the mess on the underside is another thing.
    try cleaning and stitch something regular first to see if all is back to normal.
    then try free motion on some scraps with batting in between.
    good luck
    nativetexan is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    cminor
    Main
    42
    12-29-2013 11:47 PM
    Susan Hunter
    Main
    6
    09-04-2013 08:11 AM
    BellaBoo
    Recipes
    20
    06-09-2012 07:55 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is On
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter