ironing surface
#31
Originally Posted by purplemem
I have a craft table that Michael's sells. It has an electrical outlet on it. I place a double layer of insul-brite on it, then cover with folded fabric. This is my ironing table. When I need to cut, I take the fabric off and put the cutting mats on. :D
I had my dh cut a piece of pegboard to place over the craft inserts (think holes to put cups in for paints) and I place my iron on that, with a silicon base for when the iron is hot.
Very convenient and good surface size.
I had my dh cut a piece of pegboard to place over the craft inserts (think holes to put cups in for paints) and I place my iron on that, with a silicon base for when the iron is hot.
Very convenient and good surface size.
#32
Originally Posted by purplemem
I have a craft table that Michael's sells. It has an electrical outlet on it. I place a double layer of insul-brite on it, then cover with folded fabric. This is my ironing table. When I need to cut, I take the fabric off and put the cutting mats on. :D
I had my dh cut a piece of pegboard to place over the craft inserts (think holes to put cups in for paints) and I place my iron on that, with a silicon base for when the iron is hot.
Very convenient and good surface size.
I had my dh cut a piece of pegboard to place over the craft inserts (think holes to put cups in for paints) and I place my iron on that, with a silicon base for when the iron is hot.
Very convenient and good surface size.
#33
I do know that using a solid board top will warp eventually from the steam. Using a pine board the sap that is in it will eventually bubble out of the wood. Best thing to do is make a frame and ad braces underneath out of oak or any good hard wood and use peg board for the top as it lets the steam thru. You may have to in time change the peg board but it is cheap.
#34
Super Member
Join Date: Jun 2010
Location: Bay Area near San Francisco
Posts: 1,213
Originally Posted by twinkie
If it were me, I would use insulbrite under the batting also. It would also help to protect the wood. However, I am sure you could make one.
#35
I have a small iron board, right next to my machine. I made it from a TV table. Covered first with aluminum foil then batting and muslin.
It is soooo handy sitting by my machine. Easy to take to a class and nice because it does not take up my sewing space.
It is soooo handy sitting by my machine. Easy to take to a class and nice because it does not take up my sewing space.
#36
You ladies are so full of good ideas.
I purchased my 5 ft. folding table at an office supply store. It has a handle at one end (when folded) and wheels at one end, you can pull it along behind you, much easier than carrying it. The cost was 10.00 more than purplemem's but worth it to me.
I purchased my 5 ft. folding table at an office supply store. It has a handle at one end (when folded) and wheels at one end, you can pull it along behind you, much easier than carrying it. The cost was 10.00 more than purplemem's but worth it to me.
#37
I used regular pine plywood and covered it first with a contractors garbage bag (heavyduty garbage bag). Then covered it with batting and then canvas. I made a covering like a pillow case so that I could easily replace or wash it if it got too full of starch or scorch it. It has not warped and is in perfect shape. I have used it about 2-3 years. I also made a smaller one to take to class.
#38
Originally Posted by tjradj
Originally Posted by katiebear1
Originally Posted by Aunt Doggie
Ditto on the foil covering over the wood! :-)
#39
Ironing boards used to be wooden. I have two that are very old, but sturdier than the aluminum ones. One is in the sewing room and the other in the laundry room. The ironing platform made for the one in the sewing room is made of wood also and not protected by foil, insulate or anything. I use it lots, and have not had problems.
Thread
Thread Starter
Forum
Replies
Last Post
craftybear
Links and Resources
0
01-20-2011 10:26 PM
craftybear
Links and Resources
14
11-28-2010 09:07 AM