Will the Real 15 clone please stand up
#133
Super Member
Join Date: Feb 2012
Posts: 8,091
Yes it can. I've done two or three. The cord simply goes into the motor housing then splits off and goes two directions. All you do is unsolder the cord where it's soldered to the motor wires and remove it.
Some have a plastic stress relief that holds the cord and others have a weird knot just inside the housing to prevent the wire from pulling on the motor wires.
Once you get the motor apart, clean it well but carefully. Clean the commutator so the brushes get good contact, it's a good time to replace them if needed. Clean up the bearing or bushing area as well. And if there are no external lube holes this is a good time to lube them. Most have some sort of lube, grease or oil. You just gotta figure out how to get it in.
After all that you put it back together and plug it in.
Joe
Some have a plastic stress relief that holds the cord and others have a weird knot just inside the housing to prevent the wire from pulling on the motor wires.
Once you get the motor apart, clean it well but carefully. Clean the commutator so the brushes get good contact, it's a good time to replace them if needed. Clean up the bearing or bushing area as well. And if there are no external lube holes this is a good time to lube them. Most have some sort of lube, grease or oil. You just gotta figure out how to get it in.
After all that you put it back together and plug it in.
Joe
#134
Senior Member
Join Date: Mar 2010
Location: Arkansas
Posts: 420
Thanks Joe, that sounds exactly like what my husband did. He tried to tell what he was doing, but that's not something I'm good at. I cleaned everything else up and that motor was on the Commander in the pic I posted. It wants to run like a bandit.
#135
Power Poster
Thread Starter
Join Date: Mar 2011
Location: Somewhere
Posts: 15,506
I shot a whole family - baby bear, momma bear and daddy bear? Well, not really, they all have Japanese 15 tension plates and bobbins. The slide plate is smaller on Momma bear. [ATTACH=CONFIG]326212[/ATTACH][ATTACH=CONFIG]326213[/ATTACH][ATTACH=CONFIG]326214[/ATTACH][ATTACH=CONFIG]326215[/ATTACH][ATTACH=CONFIG]326216[/ATTACH]
#136
Power Poster
Thread Starter
Join Date: Mar 2011
Location: Somewhere
Posts: 15,506
http://www.quiltingboard.com/vintage...5125057further discussion on there - if nothing else look for window #33315 to start.
#137
Super Member
Join Date: Dec 2011
Location: Northern CA near Sacramento
Posts: 1,107
Miriam,
Here is a pix of my 3/4 sized class 15 "Noname" with a stitch length lever that is a different stylethat most of the class 15s. I also added a pix of my Cinderella.
Cathy
[ATTACH=CONFIG]326269[/ATTACH][ATTACH=CONFIG]326270[/ATTACH]
Here is a pix of my 3/4 sized class 15 "Noname" with a stitch length lever that is a different stylethat most of the class 15s. I also added a pix of my Cinderella.
Cathy
[ATTACH=CONFIG]326269[/ATTACH][ATTACH=CONFIG]326270[/ATTACH]
#138
Super Member
Join Date: Feb 2012
Posts: 8,091
Cathy,
That stitch lever is reminiscent of the one on my 66-18. Kind of goofy looking in my opinion.
If I had some wood working tools and space to use them I'd make my own machine cases. I have a design in my brain I'd like to build.
Joe
That stitch lever is reminiscent of the one on my 66-18. Kind of goofy looking in my opinion.
If I had some wood working tools and space to use them I'd make my own machine cases. I have a design in my brain I'd like to build.
Joe
Thread
Thread Starter
Forum
Replies
Last Post
OurWorkbench
For Vintage & Antique Machine Enthusiasts
106
03-14-2016 04:40 PM
olebat
For Vintage & Antique Machine Enthusiasts
14
04-06-2013 03:54 PM