evelyn5269

I practice a lot and on small pieces it is fine. My stitches are fine except that some are really long and some are really short. Should I be going slower, faster. I have a Juki TL2010 Q and absolutely love it. Sews like a dream but it is me cause I had same issue on my Hsqvarna SapphireQ. I know it could probably be a lot of things, how I drape the quilt etc but if you have any things for me to try I am open.
Thank you

Mdegenhart

It's necessary to maintain an even speed and keeping your fabric moving, but not too fast or slow. I can "hear" when I am in the right zone, but it takes lots of practice to maintain the consistency. Some days I just can't hit that sweet spot.

Raggiemom

Moving your hands and the fabric at a steady consistent speed is key. And I don't always achieve that!

DogHouseMom

Agree with the others, it's all about maintaining a constant balance between machine and hand speed.


1) Relax your shoulders. Tensing them makes it more difficult to maintain a constant speed.
2) Hopefully you have the machine set into the table for a broad flat surface, and the height of the machine is at your proper ergonomic height (roughly at height of elbow).
3) If you have a speed control and on/off button on your machine (as opposed to using the foot pedal), try that to maintain a constant speed on your machine.
4) Keep practicing!! Don't worry about the design you are trying to stitch, just concentrate on maintaining the stitch length.

Lastly ... it doesn't have to be perfect. It's not unusual to have a slightly smaller stitch length around tighter curves.

QuiltE

Good points DHMom and I'll add to your list ....
5) Be aware of how you are moving the quilt as you stitch. I have caught myself letting it somewhat jump and thus creating that longer stitch. Is your table top smooth/slippery? I clean and polish it up good before I start FMQing, and if it is a longer project, repeat as needed.
6) Check is it a "long" stitch" or one being caused by the top/bottom threads not meeting/catching. Might be time for a new needle. Or it could be you need a different size and/or type of needle.
7) Drag can be created not just by the quilt hanging off the edge of the table, but also, with how you have it sitting or puddled on the table top. Watch you aren't catching it on the corner or even with the way it flops over the front towards you.
8) Echoing DHMom's #1)+#2), for me I find I need to sit a little higher when FMQing than when I am piecing. A good adjustable chair is worth the extra cost.

And as we all, already know ...... practice practice practice!
And if you are like me ... I hate that word ... I want perfection immediately! So instead of outright practice toss aways, one of the things I have done is to make squares for my practice pieces that will eventually become QAYG quilt. Some make dozens of placemats ... and there are lots more possibilities!

Keep at it ... you're probably doing better than you give yourself credit for.

ManiacQuilter2

For even stitches, you must learn how to hit a certain speed on your DSM and be able to move the fabric at the same rate as your DSM moves it. Some quilters find at a higher speed that their curves are smoother. I have always found looking at where you are wanting to go rather than looking at where your needle is may help improve your stitches. One on one class instructions at your LQS may help you get over the hump. We all didn't learn how to drive a car in a few days. Hang in there and keep practicing because it will suddenly all just click together.

Cari-in-Oly

Everyone has given you good advice, I can't really add to it but I will say that I don't worry so much about my stitches looking perfect. I'm happy if I don't have skipped stitches or eyelashes. I know I'm not making a show quilt and the recipients of my quilts don't care if the stitches aren't perfectly even. We are always our own worst critic. Once I relaxed and gave up my quest for perfection, deciding that done is better than perfect, my quilting actually got much better.

Cari

slbram17

I know, same here. If it doesn't jam and the stitches are for the most part, distinct on the back, I am ok for the most part..

Tartan

It is hard to get perfect stitches, even long arm quilts I've studied have varied stitch length. I do a fairly good job since I got my Bernina with the stitch regulator. That was one of the main reasons I got it. I didn't have many long stitches but I did have what I call "micro" stitches. So tiny and close together they were hard to remove. My BSR has fixed that.

JennC

This is a good thread!! I was just searching for tips on stitch length!!