Mizzhunybee

Hello all,
I'm new to the board, not new to quilting, which is why I'm a little frustrated. I haven't quilted in a while, took my machine in for service and now I'm having troubles when I start stitching on to the fabric, like those first few stitches get all mucked up. I've adjusted my tension, changed my needle, my stitch length at 2 1/2, I'm at a loss. Any advice?

Thanks in advance.
Michelle

PS, I'm looking forward to poking around the boards!

Kitsie

Can you use a "leader"? Put a scrap of fabric under the needle and sew to the edge and then feed the "real" fabric under the needle right behind it. Good luck and welcome!

PaperPrincess

Welcome!
As Kitsie suggested, use a leader (a scrap of fabric), and make sure that you are holding on to both bobbin and top thread tails.

bearisgray

is there a link to illustrate this? i am using a phone and have not figured out how to add a " link"

Rhonda K

Does this help you?

http://quiltville.blogspot.com/2005/...-and-hows.html

Another one for you that describes the technique.

http://quiltsbyjen.ca/what-are-leaders-and-enders/

Enjoy!

Boston1954

I have the same thing happen to me sometimes. I hold the two threads with one hand and do a couple of stitches. It helps a lot.

OurWorkbench

I don't know what machine you have. If it has a "needle up" position, it shouldn't be a problem. If it is an older mechanical machine, they used to teach that one should hold the threads behind the presser foot when you start a seam. We were talking about it at our get-together this morning and Diane mentioned that she saw instructions in the 301 manual which can be found at http://www.singerco.com/uploads/down...d14d6145d0.pdf On the bottom of page 8 of the pdf (pg 16 of the manual) the paragraph above the ""NOTE:" it tells how to lay the treads so that when lower presser foot the threads will be firmly held. At the top of page 9 in bold is to make sure thread take-up lever is at its highest position. Then lower needle into fabric, lower presser foot, sew. She told us her mantra is "Needle down......foot down......sew" and it works for all machines.

You might want to try that.

Janey - Neat people never make the exciting discoveries I do.

Irishrose2

Take out the bobbin case, if the machine has one, and check for any caught threads. Reroute the thread carefully and try stitching while holding the threads for two stitches. I find more bobbin problems that top problems with the problem you describe. Also rethread the top thread paying attention to alignment between the tension disks.

If you promise not to laugh, I'll tell you what I've done more than once - skipped the thread take up hole when threading the top. The result is what you describe, but I'm sure I'm the only one who does that. In my defense, the machine I do that on has the thread take up around toward the back.

zozee

This is a really common problem, easily solved. I'm wondering, though, before you try the methods above, if your stitches are going smoothly otherwise? Take a scrap and try starting your stitching about a inch from the end. Start with needle down, then make sure the presser foot is down, then sew. Everything smooth this way or is the thread flying out of the needle hole? are you getting any birds' nests under the fabric ? any foul sound (other than maybe bad words --LOL). If there's any of that, then rethread the machine, change tension little by little, till the stitches in are looking good.

Some needles just need to "take a bite" out of fabric when they start, and sometimes the bite isn't big enough, so it lands in the feed dogs. Using "leader" or scrap ahead of the "good" fabric you're sewing , will let your needle take that bite.

elnan

I have been sewing for over 70 years and have always held the bobbin and top threads when I start a seam. When I sew with a group, most of them are Bernina owners, and when they hear me suggest to someone having snarled nests of thread problems, "Hold onto the threads for a few stitches when you start.", someone will always tell me that is not needed except for very old machines. Not all machines or operators are the same and better safe than sorry.