help with 3D bow tie
#1
Super Member
Thread Starter
Join Date: Aug 2009
Location: Illinois
Posts: 1,821
help with 3D bow tie
Looking for tips on how to keep from catching the loop of the tie in the seam. I thought this would be easy but it gets caught so the ripper and I are getting well acquainted for no more difficult that this block should be! Anybody with experience to help will be greatly appreciated!
#2
Sorry I can't help but I would like to see a photo of the 3D bow tie block. It sound interesting...i just googled it- is your trouble when you quilt it or piece it?
Last edited by toogie; 07-03-2019 at 06:21 AM.
#3
I recently finished making a 3-d bow tie for my niece's graduation. Since I am still working on the back the only thing I can show you is a not so good pic of the wrinkled top. I pined all 3 points. The middle where the seams met at at each end of the dimensional middle of the block. I found that pinning made it much easier and my accuracy was close to perfect on each block. Here is a link to a good video: https://www.youtube.com/watch?v=BVdfuGgtHf8 . Here is a pic of the quilt I am still working on.
#4
Super Member
Thread Starter
Join Date: Aug 2009
Location: Illinois
Posts: 1,821
I love listening to this demonstrator but she didn't address how to keep that bias knot from getting into the seam allowance. She did put a finger into that to hold it out but didn't address the need for that. I'm learning!! It is certainly a quick block, much better than the traditional way. One tip I can pass along. I'm working with men's shirts. If you are working with stripes and want the knot to go the same way as the ends of the tie, turn that folded piece the opposite way and it will turn out well. (The 5" blocks would have the stripe north/south and the folded one goes east/west.)
#5
#6
Super Member
Join Date: Nov 2011
Location: Tn
Posts: 9,014
I started one of these to use up scraps. I decided a small lap quilt was enough. I found that I could stitch to the center seam. Then stop with needle down and adjust the knot and had to sort of twist the blocks to line up for the rest of the seam. Yep, the small quilt was enough to get that one off my bucket list
#8
Super Member
Thread Starter
Join Date: Aug 2009
Location: Illinois
Posts: 1,821
#9
I have made a 3D bow tie quilt and didn't have problems sewing things together but I did mine differently that the tutorial listed above. Sorry but I don't have a picture to share.
Here is the method I used. There is hand sewing involved but that is what I liked about it. It was a project I could start away from the machine and then when my blocks were done I assembled the quilt top on the machine.
http://mylifeisastitch.<wbr>blogspot.com/2011/12/fabric-<wbr>folding-one-bow-tie-obsessed.<wbr>html
I know this doesn't help with the question asked but for those of you who might like to make a 3D bow tie quilt this is another option that doesn't have seam issues.
Here is the method I used. There is hand sewing involved but that is what I liked about it. It was a project I could start away from the machine and then when my blocks were done I assembled the quilt top on the machine.
http://mylifeisastitch.<wbr>blogspot.com/2011/12/fabric-<wbr>folding-one-bow-tie-obsessed.<wbr>html
I know this doesn't help with the question asked but for those of you who might like to make a 3D bow tie quilt this is another option that doesn't have seam issues.
#10
I used the same method as citruscountyquilter, and made them all on a road trip to CT and back. As the tute says, they are addicting. Here is my quilt using 1 charm pack and plain white sqs.
[ATTACH=CONFIG]614545[/ATTACH]
[ATTACH=CONFIG]614546[/ATTACH]
[ATTACH=CONFIG]614545[/ATTACH]
[ATTACH=CONFIG]614546[/ATTACH]
Thread
Thread Starter
Forum
Replies
Last Post
Butterfli19
General Chit-Chat (non-quilting talk)
3
10-19-2013 05:41 AM