Blocking a block to stretch it - - -
#1
Power Poster
Thread Starter
Join Date: May 2008
Location: MN
Posts: 24,659
Blocking a block to stretch it - - -
I am thinking if a block is smaller than the other ones - and it is blocked to stretch it - that the next time it is washed it will revert back to being smaller again.
Like my jeans stretch out after being worn a while- but the next time they are washed, they are tight again.
I can see/understand shrinking a block to fit - but the idea of stretching it really goes against my grain.
Is my thinking wrong?
Like my jeans stretch out after being worn a while- but the next time they are washed, they are tight again.
I can see/understand shrinking a block to fit - but the idea of stretching it really goes against my grain.
Is my thinking wrong?
#2
Power Poster
Join Date: Nov 2009
Location: Mableton, GA
Posts: 11,330
I don’t know if it is wrong but if it is just a teensy but off once it is sewn together and quilted and washed would it be noticeable? Of course a major difference would mean remake the much smaller block. At least that’s what I would do
#3
Stretching won't last. Don't bother.
If the block is a bit smaller than the others, "alter" a seam or two to give yourself the additional amount to get it to size. Usually a block ends up smaller because you took up just a tad too much in one or more seams.
If the block is a bit smaller than the others, "alter" a seam or two to give yourself the additional amount to get it to size. Usually a block ends up smaller because you took up just a tad too much in one or more seams.
#4
not wrong. your thinking is the same as mine as soon as i saw your title. i would never use a block that must be stretched to fit. i'd make another or redo some seams a hair narrower if i didn't have any other fabric to use.
#5
On the rare occasion I have a block a bit too small and I have run out of fabric to make another, this is what I do. Cut a strip of fusible lining the length of the seam(s) overlapping slightly so that when it is sewn to the next piece it is fused when it is pressed. You only have to be careful not to iron over the overlapped piece when you attach it to the first piece.
#6
I have done something similar but only when the block is "titch" small. No problems later on. Some times a quick spray of water or spray starch them press, and it will make the block the correct size. Trying to gain a 1/4 inch or heavens more, I would return to the block and resew some of the seems to the scant 1/4 in in a couple of seems and then the total block will be the correct size.
#7
Power Poster
Thread Starter
Join Date: May 2008
Location: MN
Posts: 24,659
At one time, Sharon Schamber had a youtube video on stretching a block - which I was unable to find again last night.
I was very surprised about it when I saw it at the time.
I did manage to stretch a 5 inch block to about 5-1/2 inches (unintentionally!) by sopping it with spray starch and ironing it out when it was wet like I was rolling pie crust.
I have learned so much by doing things incorrectly the first time!
I was very surprised about it when I saw it at the time.
I did manage to stretch a 5 inch block to about 5-1/2 inches (unintentionally!) by sopping it with spray starch and ironing it out when it was wet like I was rolling pie crust.
I have learned so much by doing things incorrectly the first time!
#9
Super Member
Join Date: May 2012
Location: Central Wisconsin
Posts: 4,391
On the rare occasion I have a block a bit too small and I have run out of fabric to make another, this is what I do. Cut a strip of fusible lining the length of the seam(s) overlapping slightly so that when it is sewn to the next piece it is fused when it is pressed. You only have to be careful not to iron over the overlapped piece when you attach it to the first piece.
Thread
Thread Starter
Forum
Replies
Last Post