seam allowance when binding on quilt
#22
Super Member
Join Date: May 2011
Location: Pacific NW
Posts: 9,561
There's only rules about quilts you're entering to be judged. I just sewed a 1" binding on a baby quilt and I love how it turned out. It's a lot softer than regular binding, which can sometimes feel almost like a cord at the edge of the quilt.
#24
Junior Member
Thread Starter
Join Date: Nov 2016
Posts: 106
I don't trim off my batting until after I've put on the first machine stitching of the binding, and I use that seam for my measurement.
I cut my bindings a bit fuller than most, at 3" and so I trim .5" from that seam line for a nice full binding. When we say "full" that doesn't mean round, just the same as the body of the quilt.
If you have a half inch finished binding and you trimmed everything at 1/4" that means half your binding is empty.
You can add in little wisps of left over batting if you need to.
Edit: It's not that big a deal really, but if you want to show your quilts it is expected (along with mitered corners). Doesn't impact the kindness of a gift or the durability of the quilt. For the first couple of decades of my quilting I used straight bindings with butt joints. Decided to switch to bias French double fold binding and miter corners because that was the expectation/standard but mostly I just say Boo to the quilt police
I cut my bindings a bit fuller than most, at 3" and so I trim .5" from that seam line for a nice full binding. When we say "full" that doesn't mean round, just the same as the body of the quilt.
If you have a half inch finished binding and you trimmed everything at 1/4" that means half your binding is empty.
You can add in little wisps of left over batting if you need to.
Edit: It's not that big a deal really, but if you want to show your quilts it is expected (along with mitered corners). Doesn't impact the kindness of a gift or the durability of the quilt. For the first couple of decades of my quilting I used straight bindings with butt joints. Decided to switch to bias French double fold binding and miter corners because that was the expectation/standard but mostly I just say Boo to the quilt police
Idle Di
Last edited by QuiltnNan; 12-24-2019 at 03:30 AM. Reason: shouting/all caps
#25
Junior Member
Thread Starter
Join Date: Nov 2016
Posts: 106
This is what I do. I trim the binding and back just enough so that there isn't so much in my way. I sew the binding on with a 1/4 in seam. (Sometimes that is very necessary to save points.) Then I measure from the seam I have just sewn for the correct width to make the binding full after it is turned to the other side.
Silly question though, how do you make sure that the front of the quilt where you are sewing is level and straight without cutting the edging off.
Idle Di
#26
Junior Member
Thread Starter
Join Date: Nov 2016
Posts: 106
#27
Junior Member
Thread Starter
Join Date: Nov 2016
Posts: 106
Good question, and that is another one for me to find the answer to
Idle Di
#28
Junior Member
Thread Starter
Join Date: Nov 2016
Posts: 106
#29
I normally use a 2" strip, press in half and use a 1/4" seam allowance. I sew to the back first and fold over to the front of the quilt. My bindings are very narrow and I try to make them so they don't take away from the quilt top.
When using a 2-1/2 inch binding, I use a 3/8 inch seam allowance.
When using a 2-1/4 inch binding, I use a 1/4 inch seam allowance.
Nice thing is that there are no "Quilt Police". Find what you like best and run with it. It will be beautiful.
When using a 2-1/2 inch binding, I use a 3/8 inch seam allowance.
When using a 2-1/4 inch binding, I use a 1/4 inch seam allowance.
Nice thing is that there are no "Quilt Police". Find what you like best and run with it. It will be beautiful.
Thread
Thread Starter
Forum
Replies
Last Post
craftybear
Links and Resources
5
10-01-2011 07:09 PM
craftybear
Links and Resources
6
10-01-2011 07:03 PM
craftybear
Links and Resources
4
10-01-2011 07:02 PM