Using starch - cleaning the iron afterwards
10-18-2018, 01:01 AM
#12
Super Member
Thread Starter
Join Date: Mar 2011
Location: South Yorkshire UK
Posts: 1,145
Good idea. I think I’m going to have buy a new iron, as the old one is past being cleanable. This might help me keep the new one clean.
10-18-2018, 01:02 AM
#13
Super Member
Thread Starter
Join Date: Mar 2011
Location: South Yorkshire UK
Posts: 1,145
10-18-2018, 01:05 AM
#14
Super Member
Thread Starter
Join Date: Mar 2011
Location: South Yorkshire UK
Posts: 1,145
I don’t always use it, because of this problem, but when I’m dealing with fabric cut on the bias or fabric that’s not of the best quality, the stiffness it gives does help.
10-18-2018, 01:07 AM
#15
Super Member
Thread Starter
Join Date: Mar 2011
Location: South Yorkshire UK
Posts: 1,145
I just use plain old water to clean the sole plate. Here's how I was taught how to starch: when your iron gets all gunky, it's because when you’re ironing,and the fabric hasn't had a chance to absorb the starch, what you're doing is, instead of ironing the fabric, you are ironing the starch. I starch every piece of fabric I'm going to work with, at least 2 hours ahead of the time, throw it in a large ziplock bag, and let it sit, then I'll take it out, either line dry or throw in the dryer for a few minutes, then iron, have never had a problem with the iron getting all gunky then, I do spray mist with water since I don't use the steam on my iron.
10-18-2018, 02:40 AM
#17
Super Member
Join Date: Mar 2011
Location: Central NJ
Posts: 5,571
I had this issue just the last couple of days. I normally use Sta-Flo liquid starch in a 50/50 mix. I let the starch soak into the fabric for a few minutes and start ironing. Well, I ran out of Sta-Flo and my local grocery store only had 'Linit' brand. I think it has a lower scorch point than the Sta-Flo. So I ended up having gunk all over my iron. Of course, could not find the Iron Off cleaner so had to purchase a different brand of that yesterday. Not quite as good as Iron Off but it did work.
You squeeze the goo on a piece of terrycloth, rub your hot iron on it and the gunk comes off. Clean iron once again. Yippee! BTW, I also purchased more Sta-Flo. Will put the other jug aside and only use if I have another starch emergency, lol.
You squeeze the goo on a piece of terrycloth, rub your hot iron on it and the gunk comes off. Clean iron once again. Yippee! BTW, I also purchased more Sta-Flo. Will put the other jug aside and only use if I have another starch emergency, lol.
10-18-2018, 06:24 AM
#18
Super Member
Join Date: Sep 2011
Location: Carroll, Iowa
Posts: 3,415
I found if you starch from the bottom side and press on the top side, it keeps the starch from collecting on your iron. I normally starch my fabrics using the dunk, squeeze thru a wringer and hang method. So the starch is on both sides but I have never had an issue with starch getting on my iron. If I have to spray more starch on the block I starch from the back side and then press. If you let the starch soak in before you press, that also will help with the buildup.
As to cleaning your iron of the buildup, I use Dritz's "Iron Off" in a tube found in the sewing dept of Walmart. I put some on an old rag and run my iron over the stuff. It may take a couple times depending on how much buildup you have but it works great for me. I haven't had to use it in some time now.
[
As to cleaning your iron of the buildup, I use Dritz's "Iron Off" in a tube found in the sewing dept of Walmart. I put some on an old rag and run my iron over the stuff. It may take a couple times depending on how much buildup you have but it works great for me. I haven't had to use it in some time now.
[
Thread
Thread Starter
Forum
Replies
Last Post
woohoowendy
Main
12
04-02-2011 02:02 AM
