Clutch will not engage
#11
Actually, I'm not sure you absolutely have to have it. Have you tried holding the hand wheel and tightening the knob as far as you can? It sounds like the washer is in the correct position as it did sew some. The screw just keeps it in position so that it doesn't unscrew all the way off. I think there may be some that actually screw into the washer, but not yours. It should be like the links like I sent before.
I'm pretty sure you just tighten the knob finger tight and then put the screw in. Someone described the purpose of the "pin" "screw" at Stop Motion problem
I hope you can find it.
There aren't many sewing machine repair shops around, but you may be able to find one that has an old parts bin that may have one. There are new ones available, but several different sizes. I could try removing one and tying it in another machine - it isn't like I don't have a variety of machines to test .
Janey - Neat people never make the exciting discoveries I do.
I'm pretty sure you just tighten the knob finger tight and then put the screw in. Someone described the purpose of the "pin" "screw" at Stop Motion problem
I hope you can find it.
There aren't many sewing machine repair shops around, but you may be able to find one that has an old parts bin that may have one. There are new ones available, but several different sizes. I could try removing one and tying it in another machine - it isn't like I don't have a variety of machines to test .
Janey - Neat people never make the exciting discoveries I do.
Last edited by OurWorkbench; 01-08-2021 at 06:12 AM.
#12
Super Member
Join Date: Mar 2016
Posts: 2,834
If you do need to go to a sewing machine repair place to get a replacement, just unscrew the inner wheel and take it with you to make sure the screw will fit.
bkay
#13
[QUOTE=bkay;.
If you do need to go to a sewing machine repair place to get a replacement, just unscrew the inner wheel and take it with you to make sure the screw will fit.
bkay[/QUOTE]
Nice description on Janey's last post. If you do end up taking the clutch knob/wheel in, be careful as you take it apart and put it together. The two inner washer lobes must fit in the shaft right and if the washer falls off and turns over you will be in for a lot of trial and error figuring out which way it goes. But bkay is right., beats carrying in a whole head.
If you do need to go to a sewing machine repair place to get a replacement, just unscrew the inner wheel and take it with you to make sure the screw will fit.
bkay[/QUOTE]
Nice description on Janey's last post. If you do end up taking the clutch knob/wheel in, be careful as you take it apart and put it together. The two inner washer lobes must fit in the shaft right and if the washer falls off and turns over you will be in for a lot of trial and error figuring out which way it goes. But bkay is right., beats carrying in a whole head.
#15
#16
Member
Thread Starter
Join Date: Jan 2021
Location: Charlotte, NC
Posts: 9
Actually, I'm not sure you absolutely have to have it. Have you tried holding the hand wheel and tightening the knob as far as you can? It sounds like the washer is in the correct position as it did sew some. The screw just keeps it in position so that it doesn't unscrew all the way off. I think there may be some that actually screw into the washer, but not yours. It should be like the links like I sent before.
I'm pretty sure you just tighten the knob finger tight and then put the screw in. Someone described the purpose of the "pin" "screw" at Stop Motion problem
I hope you can find it.
There aren't many sewing machine repair shops around, but you may be able to find one that has an old parts bin that may have one. There are new ones available, but several different sizes. I could try removing one and tying it in another machine - it isn't like I don't have a variety of machines to test .
Janey - Neat people never make the exciting discoveries I do.
I'm pretty sure you just tighten the knob finger tight and then put the screw in. Someone described the purpose of the "pin" "screw" at Stop Motion problem
I hope you can find it.
There aren't many sewing machine repair shops around, but you may be able to find one that has an old parts bin that may have one. There are new ones available, but several different sizes. I could try removing one and tying it in another machine - it isn't like I don't have a variety of machines to test .
Janey - Neat people never make the exciting discoveries I do.
#17
Member
Thread Starter
Join Date: Jan 2021
Location: Charlotte, NC
Posts: 9
Nice description on Janey's last post. If you do end up taking the clutch knob/wheel in, be careful as you take it apart and put it together. The two inner washer lobes must fit in the shaft right and if the washer falls off and turns over you will be in for a lot of trial and error figuring out which way it goes. But bkay is right., beats carrying in a whole head.