Need help keeping ruler from slipping when cutting fabric
04-06-2014, 04:46 AM
#71
Senior Member
Join Date: Apr 2009
Location: North Florida
Posts: 976
Just yesterday I received the monthly newsletter form Jinny Beyer, she discover & passed on to us that she now uses the "Needle Grip'It's" (that you use on your finger tips for pulling needles when quilting), She places those on the back of her templates & rulers to keep them from moving. I have some of those so next time I'm going to try it.
04-06-2014, 04:54 AM
#72
Junior Member
Join Date: Jul 2012
Location: South Carolina
Posts: 213
I use "Grip Strips." They are clear and have adhesive on one side to stick to the ruler or template. I love them. http://www.guidelines4quilting.com/GripStrips.html
04-06-2014, 06:20 AM
#73
Junior Member
Join Date: Jun 2012
Posts: 176
Thanks for all the suggestions. I also tried the plastic dots and sandpaper, but found the clear plastic better. I am just not able to apply enough pressure with hand alone. Walking up the fabric didn't work either and neither did folding fabric in half again. Will defintely try shower thingies.
The the best thing I have found lately are Steady Betty strips. They came as multiple strips in a small pkg. in the notions and are cut in small pieces and placed on the back of the ruler. They really hold the ruler to the fabric.
04-06-2014, 08:21 AM
#75
Power Poster
Join Date: Oct 2010
Location: Mississippi
Posts: 27,298
The clear plastic dots stopped that for me. You have to put enough of them on there... about every 6" should have a dot. I also only put pressure from the cutter in the area where my hand is. I stop and move my hand before going up farther, and the ruler doesn't move.
04-06-2014, 08:28 AM
#76
Member
Join Date: Dec 2011
Posts: 55
http://quiltville.blogspot.com/2013/...-slippage.html
I use this tip from Quiltville about using bandage tape to stop slippage. It works wonderfully!
I use this tip from Quiltville about using bandage tape to stop slippage. It works wonderfully!
04-07-2014, 10:39 AM
#77
Super Member
Join Date: Nov 2006
Location: Central PA
Posts: 1,920
Slipping ruler
I don't recall where I heard this suggestion, but I tried it and it works. Purchase a cheap bottle of clear fingernail polish. Paint a strip on the back of the ruler and then sprinkle on table salt. Do one area at a time. I did this about two months ago and the salt is still in place and still working. Cheap and effective.
04-07-2014, 10:05 PM
#79
Super Member
Join Date: Jun 2010
Location: England Alton Towers
Posts: 6,673
I went out to cheap sales and purchased at very low cost scale weights not complete sets the heaviest the best after a wrist operation. I put the weights down the side of the ruler which did help as well as auctions from car departments are stronger than others and also heavy.
04-08-2014, 06:01 AM
#80
Super Member
Join Date: Apr 2012
Posts: 1,165
I like Quilter's slidelock. The Quiltcut is nice if you have a permanent place for it. I have an executive desktop for a cutting table, and the table is used for other things. I set up for macro photography, cut my own mats for pictures, do papercrafting, etc, and the Quiltcut is heavy. You can't just take it off the table and lean it against a wall. I'd have the same problem with an Accuquilt. I have a Sizzix Big Shot and it doesn't get much use as I don't have room to leave it out.
Thread
Thread Starter
Forum
Replies
Last Post
Sunnie
General Chit-Chat (non-quilting talk)
37
05-09-2014 04:03 PM
