Go Back  Quiltingboard Forums >
  • Main
  • Queen Supreme Super Slider? >
  • Queen Supreme Super Slider?

  • Queen Supreme Super Slider?

    Thread Tools
     
    Old 08-14-2015, 01:23 PM
      #1  
    Senior Member
    Thread Starter
     
    Join Date: Jul 2010
    Location: Westcliffe, CO
    Posts: 793
    Default Queen Supreme Super Slider?

    I was just about to order one of these but I'm not sure if it will be to big for my machine. I have a Pfaff 2140. Can anyone tell me how many inches it is from the hole to the edge of the slider. My machine is 7 inches from the needle to the sewing machine. Any help would be greatly appreciated!
    Dreaming is offline  
    Old 08-14-2015, 01:26 PM
      #2  
    Super Member
     
    Join Date: Apr 2012
    Posts: 1,165
    Default

    I have the regular size and the cut out hole for the needle is in the center. I'd assume the same for the queen size.

    Ad says slider is 11 1/12 x17. It might be tight but the center of 11 1/2 is a tad less than 6 inches.
    Do you have a table or is the machine inset? The 17 inch length could be a problem.

    Last edited by Weezy Rider; 08-14-2015 at 01:29 PM.
    Weezy Rider is offline  
    Old 08-14-2015, 05:30 PM
      #3  
    Super Member
     
    GEMRM's Avatar
     
    Join Date: Nov 2011
    Location: South West Ontario
    Posts: 2,237
    Default

    I don't know the space from side to needle cut out, but if you have enough room on the other 3 sides, you could always trim that one edge?
    GEMRM is offline  
    Old 08-14-2015, 05:57 PM
      #4  
    Member
     
    FairviewFarm's Avatar
     
    Join Date: May 2013
    Location: Wisconsin
    Posts: 39
    Default

    I have a Queen Supreme Slider. The hole is not centered in this size slider. The following measurements are to the center of the hole.

    When the slider is oriented horizontally (so the length is running left to right), the hole is 6 7/8" from one side and 9 7/8" from the other.

    If the slider is oriented vertically (the length running front to back), the hole is 5 3/4" from either side.

    I have a Pfaff Performance 5.0. When I place the Slider horizontally with the 9 7/8" to the right of the hole, it fits perfectly.

    Two other less expensive options you might try are:

    http://forum.missouriquiltco.com/loo...esome-fmq.html

    http://thequiltrat.blogspot.com/search/label/sew%20slip

    I recently bought an oven liner and plan to give the first option a try as my machine is in a cabinet with a plexiglass insert (like the original poster) and I wanted to cover the entire area too.

    Hope this helps.
    FairviewFarm is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    sewsewquilter
    Main
    15
    11-02-2012 07:34 PM
    Dar-midlife
    Main
    23
    10-18-2011 05:51 PM
    quiltinghere
    Main
    15
    07-23-2010 10:47 AM
    borntoquilt
    Main
    13
    02-07-2009 08:38 PM
    DebJ
    Main
    15
    06-19-2008 07:20 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is On
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter