Vintage Morse dial-o-matic info needed.
#1
Member
Thread Starter
Join Date: Mar 2016
Posts: 5
Vintage Morse dial-o-matic info needed.
I got this at an estate auction. The bed of the machine is exactly 12" by 5 1/8” wide and 8 1/2” from the bed to the top of the hand wheel. I have looked and looked everywhere I can think of and can't find any machine like this. I know it was made in Japan, as apparently all Morse machines were. Does anybody have any information on this machine? Any input at all would be greatly appreciated.
Last edited by kathy wright; 05-18-2022 at 06:21 PM. Reason: Picture didn't load
#2
Welcome to Quilting Board. I do not have any Morse machines, but have seen a lot of them here and elsewhere on the web.
My standard response for posting pictures is -- Pay attention to formatting differences.
We like pictures. In order to post pictures on Quilting Board, you will probably need to reduce or compress the picture to a file size that is smaller than 2MB. How to post images can be found at https://www.quiltingboard.com/attach...020-01-17-.pdf
Don't forget to scroll over to the far right to find and click on the "Upload" button.
I have found that only the big red "Reply" button or "Quote" work to give me the paper clip icon to work for adding pictures.
https://www.quiltingboard.com/attach...p-location.jpg
Some additional info regarding reducing images at post #4 and images for the scroll and upload button can be found at #5 of quilt block ID?
Another way to post pictures can be found at 2021/2022, 2.5” Birthday Swap
Or simply - Make sure pictures are smaller than 2MB
Click on red "Reply" button
Click on the paper clip icon
Click browse - choose picture/s. (only 5 allowed per post)
Once they show up as being loaded, Scroll over to the right side and click on "Upload"
After the pictures show up as being attached, you can close that window and go back to the screen to finish posting your post.
Janey - Neat people never make the exciting discoveries I do.
Not affiliated with off-site link(s)
My standard response for posting pictures is -- Pay attention to formatting differences.
We like pictures. In order to post pictures on Quilting Board, you will probably need to reduce or compress the picture to a file size that is smaller than 2MB. How to post images can be found at https://www.quiltingboard.com/attach...020-01-17-.pdf
Don't forget to scroll over to the far right to find and click on the "Upload" button.
I have found that only the big red "Reply" button or "Quote" work to give me the paper clip icon to work for adding pictures.
https://www.quiltingboard.com/attach...p-location.jpg
Some additional info regarding reducing images at post #4 and images for the scroll and upload button can be found at #5 of quilt block ID?
Another way to post pictures can be found at 2021/2022, 2.5” Birthday Swap
Or simply - Make sure pictures are smaller than 2MB
Click on red "Reply" button
Click on the paper clip icon
Click browse - choose picture/s. (only 5 allowed per post)
Once they show up as being loaded, Scroll over to the right side and click on "Upload"
After the pictures show up as being attached, you can close that window and go back to the screen to finish posting your post.
Janey - Neat people never make the exciting discoveries I do.
Not affiliated with off-site link(s)
#4
Super Member
Join Date: Mar 2016
Posts: 2,826
Nice machine! I would be willing to guess it's a badged machine. Which means it was made by someone else and labeled as a Morse and labeled as a "dial-o-matic" after the fact, as It has no dials. Also, the Morse badge and the dial-o-matic badge are riveted on over the decals, as opposed to being part of the decals. It's not uncommon for sewing machines made in Japan in the 1950's to be sold under different names. The nameplate being riveted is unusual.
Is it iron or aluminum (does a magnet stick to it)? Do you have the case? I would also guess that a generic 15 manual would serve as a good manual. Janey will know for sure.
I'm eagerly waiting for someone with more knowledge than me to post.
bkay
Is it iron or aluminum (does a magnet stick to it)? Do you have the case? I would also guess that a generic 15 manual would serve as a good manual. Janey will know for sure.
I'm eagerly waiting for someone with more knowledge than me to post.
bkay
#5
Senior Member
Join Date: Apr 2020
Location: South of St Louis
Posts: 822
I am intrigued by this machine. Initially it looks like a 3/4 size 15 clone (I just posted about one I recently acquired), but upon closer comparison they have two big differences: the rounded harp space, and the different stitch length adjuster.
I agree with bkay, looks like a badged machine (too bad someone attached those badges over the decals), but of what is it a clone, if it is a clone?
Janey??
I agree with bkay, looks like a badged machine (too bad someone attached those badges over the decals), but of what is it a clone, if it is a clone?
Janey??
#6
Finally, made it here. It is a "Cinderella" and there is a thread about it at Rescued Cinderella. From what I remember, they are not very good machines and actually are in two parts. They sure are cute, though.
There was also a Cinderella machine but was made in Germany as seen at Cinderella Hand Crank Sewing Machine
Janey - Neat people never make the exciting discoveries I do.
There was also a Cinderella machine but was made in Germany as seen at Cinderella Hand Crank Sewing Machine
Janey - Neat people never make the exciting discoveries I do.
#7
Member
Thread Starter
Join Date: Mar 2016
Posts: 5
Nice machine! I would be willing to guess it's a badged machine. Which means it was made by someone else and labeled as a Morse and labeled as a "dial-o-matic" after the fact, as It has no dials. Also, the Morse badge and the dial-o-matic badge are riveted on over the decals, as opposed to being part of the decals. It's not uncommon for sewing machines made in Japan in the 1950's to be sold under different names. The nameplate being riveted is unusual.
Is it iron or aluminum (does a magnet stick to it)? Do you have the case? I would also guess that a generic 15 manual would serve as a good manual. Janey will know for sure.
I'm eagerly waiting for someone with more knowledge than me to post.
bkay
Is it iron or aluminum (does a magnet stick to it)? Do you have the case? I would also guess that a generic 15 manual would serve as a good manual. Janey will know for sure.
I'm eagerly waiting for someone with more knowledge than me to post.
bkay
So apparently this isn't a Morse? As for the case - it did come with one. One that looks like it's been through the war and didn't fair well.. Check the pictures of the pitiful case and the foot pedal. Any comments, advice, would be great. Thanks.
#10
In addition to the link for the Rescued Cinderella I gave above, I found a neat post and there are some followup posts. If you click on Vintage Sewing Machine Shop.....Come on in and sit a spell and then click the link on the top right of the page that says " Vintage Sewing Machine Shop.....Come on in and sit a spell" there are some more posts about the three machines shown. (Cinderella, 3/4 size 15 clone and a full size 15 clone)
Janey - Neat people never make the exciting discoveries I do.
Not affiliated with off-site link(s)
Janey - Neat people never make the exciting discoveries I do.
Not affiliated with off-site link(s)
Last edited by OurWorkbench; 05-19-2022 at 06:40 PM.