Question about tshirt quilts
05-26-2010, 05:01 AM
#1
Super Member
Thread Starter
Join Date: Aug 2009
Location: SC
Posts: 1,309
when sewing the t shirts together do you use a straight stitch and the 1/4" seam allowance? I had someone (not a quilter) tell me to use a zig zag stitch so that the seam would stretch with the shirt. Thanks!
05-26-2010, 05:09 AM
#2
Super Member
Join Date: Feb 2009
Location: South central Nebraska, US
Posts: 5,367
I do mine by stabilizing the t shirt blocks with a non stretchy interfacing and than proceeding like a regular quilt. If you want a stretchy quilt than you would probably follow her advice although I personally would not advise that. That would mean that the rest of the quilt would all have to be stretchy fabrics. Clear as mud??
05-26-2010, 05:30 AM
#3
Super Member
Thread Starter
Join Date: Aug 2009
Location: SC
Posts: 1,309
well that was what I was thinking. I was thinking about using these tshirts as the backing on the memorial quilts I am making but just not sure how to make it work. I also don't need to spend a ton of $ on these....I still have buy the batting for them. What kind of stabilizer do you use and is it $$ to do?
05-26-2010, 05:58 AM
#4
Super Member
Join Date: Feb 2009
Location: South central Nebraska, US
Posts: 5,367
I used tricot interfacing and bought it at Joanns with a 50% off coupon and bought a whole bolt! I forget how much it is but you can check their website. Just make sure that the "stretch" in the tricot goes the opposite of the t shirt stretch when you iron it on. I always cut my t shirt block bigger and after ironing on the interfacing I trim it to size. I use the tricot for the softness but there are other light weight interfacings out there that may be cheaper.
05-26-2010, 07:10 AM
#5
Senior Member
Join Date: Jan 2010
Location: Middle America
Posts: 707
When I made this large wall hanging (notice it is over a davenport!), I used light-weight interfacing plus Warm&Natural batting. By the time I had both the quilt top and the backing, it was a very heavy pull to quilt. When I sewed the backed t-shirts together (definitely straight stitch), I used 1/2 inch seam to make sure the two back-sides of seams touched for quilting. The 1/4 inch was too small to open up. Hope you have a quilting angel sitting on your shoulder while you complete your quilt as it is going to be tough. Not knowing what the quilt top is like, might I suggest you make a separate throw with the t-shirts? Been there, done this....aching shoulder and elbow for months.
05-26-2010, 07:20 AM
#8
Senior Member
Join Date: Jan 2010
Location: Middle America
Posts: 707
Originally Posted by Deb watkins
When I did my t-shirts I used both front and back. I sewed the square together first, then I cut out the block.
05-26-2010, 08:52 AM
#9
Power Poster
Join Date: Dec 2008
Location: Western Wisconsin
Posts: 12,930
I like the nylon tricot interfacing also. It is cheaper if purchased from a drapery company online. This is where I bought mine:
http://www.bblackandsons.com/
http://www.bblackandsons.com/
05-26-2010, 10:00 AM
#10
Power Poster
Join Date: Jul 2007
Location: Out searching for some sunshine :-)
Posts: 58,856
A cheaper cotton fusible interfacing may not work as well, because I am wondering if the hotter temperature required to fuse it would hurt the tshirt fabric and the designs on them. A tricot would require less heat, and may be more gentle on the screen printings.
I have seen fusible tricot interfacing at JoAnns for less than $2yd :D:D:D
I have seen fusible tricot interfacing at JoAnns for less than $2yd :D:D:D
Thread
Thread Starter
Forum
Replies
Last Post
