Go Back  Quiltingboard Forums > Tutorials
QAYG No hand sewing! >

QAYG No hand sewing!

QAYG No hand sewing!

Old 02-08-2010, 03:24 AM
  #21  
k3n
Power Poster
Thread Starter
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

18. OK back to the original blocks ! So here are two blocks joined together with a sashing strip. Join all your blocks in rows in the same way.
Attached Thumbnails attachment-17852.jpe  
k3n is offline  
Old 02-08-2010, 03:25 AM
  #22  
k3n
Power Poster
Thread Starter
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

19. This shows the back of two blocks joined together. See how the two seam allowances nest nicely together ? You may want to press them gently into place with the point of your iron so they lay nice and flat.
Attached Thumbnails attachment-16019.jpe  
k3n is offline  
Old 02-08-2010, 03:25 AM
  #23  
k3n
Power Poster
Thread Starter
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

20. Here youíll see Iím measuring between the two stitching lines to show that they are Ĺ inch apart.
Attached Thumbnails attachment-16020.jpe  
k3n is offline  
Old 02-08-2010, 03:26 AM
  #24  
k3n
Power Poster
Thread Starter
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

21. We want to cover these stitching lines completely, so we take some ĺ inch wide steam a seam. This will extend to an 1/8th of an inch either side of the stitching lines.
Attached Thumbnails attachment-16021.jpe  
k3n is offline  
Old 02-08-2010, 03:26 AM
  #25  
k3n
Power Poster
Thread Starter
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

22. But first we have to make our backing strips. These need to be twice the width of the steam a seam, so 1 Ĺ inches wide. I donít worry about length Ė I just cut a couple across the width of the fabric then trimmed them as I went Ė to lazy to do the maths ! But if you prefer to calculate how many you need in advance, go for it ! You need a backing strip for every joint between the blocks and then long strips to cover the joints in the rows later on. My strips are in the same fabric as my backing. Itís a fairly soft, thin unbleached cotton. Try and use something soft and fine or it will get really stiff.
Attached Thumbnails attachment-18016.jpe  
k3n is offline  
Old 02-08-2010, 03:27 AM
  #26  
k3n
Power Poster
Thread Starter
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

23. Then press your backing strips in half with the iron, wrong sides together and open them out again. This gives you the centre line of your strip.
Attached Thumbnails attachment-18017.jpe  
k3n is offline  
Old 02-08-2010, 03:27 AM
  #27  
k3n
Power Poster
Thread Starter
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

24. Then you want to press each side of the strip into the middle. I press the bottom side up first, then the top side down. Itís a bit fiddly at first but it goes pretty well. DONíT burn your fingers though !
Attached Thumbnails attachment-18020.jpe  
k3n is offline  
Old 02-08-2010, 03:28 AM
  #28  
k3n
Power Poster
Thread Starter
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

25. OK Ė now we take our steam a seam and lay it over the joint on the back of the blocks, so that it extends an equal amount each side of the stitching line. I then take my scissors (NOT the best fabric ones !) and trim it to length.
Attached Thumbnails attachment-18176.jpe  
k3n is offline  
Old 02-08-2010, 03:29 AM
  #29  
k3n
Power Poster
Thread Starter
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

26. Then lay your backing strip, right side up, over the steam a seam so it covers it completely. (You'll notice these are the crazy blocks again!)
Attached Thumbnails attachment-17027.jpe  
k3n is offline  
Old 02-08-2010, 03:29 AM
  #30  
k3n
Power Poster
Thread Starter
 
k3n's Avatar
 
Join Date: Feb 2009
Location: Somerset, England
Posts: 10,686
Default

27. Then press with the iron. The instructions say to use steam but I donít Ė a dry iron is fine for a count of about 5 seconds. Weíll be stitching this down so weíre only looking for a temporary hold. Let it go completely cool before the next stage or it may come unstuck ! Once youíre underway, you can be sewing one piece together while the next piece is cooling. When itís cool, trim off the excess backing strip, flush with the edge of the block.
Attached Thumbnails attachment-18177.jpe  
k3n is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
k3n
Pictures
61
04-12-2011 12:43 AM
blzzrdqueen
Main
26
10-30-2010 06:15 PM
PatriceJ
Main
1
02-17-2008 05:04 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter