|
Originally Posted by Mizkaki
(Post 5659424)
Joe,
Picture please? Cathy I thought I had a pic of it but I didn't so I had to go take a couple. The first pick is a side view of the drive wheel with the two grommets in place of the original flat spotted friction drive. The set screw holds the drive wheel to the motor shaft. http://i119.photobucket.com/albums/o...drivewheel.jpg The second pic shows the hollow end with the flared part I filed away. The outer rim was held in by the flare only. The hole for the set screw shown here was there in both the outer rim and the shaft. All I did was put a set screw in it after putting in the grommets. http://i119.photobucket.com/albums/o...elfrtscrew.jpg Joe |
2 Attachment(s)
Joe,
Here ya go. A picture comparing the the short Boye 2 1/2needle, the 15x1 needle , and the 206x13 needle. [ATTACH=CONFIG]376815[/ATTACH][ATTACH=CONFIG]376816[/ATTACH] Cathy
Originally Posted by J Miller
(Post 5658610)
Cathy, I'll have to make a note of these numbers. The only other number besides the Kenmore 49 that I'd come up with is the Boye 2½. Are the needles you're talking about flat shank or round shank, and do you have a pic of them? I'm curious as to what the point to the eye looks like. Joe
|
Cathy,
Thanks. I saved the pics and made and noted the needle numbers for future reference. Joe |
I think I need a tutorial how to read the needles.
BTW Where is everybody? It sure is quiet around here... |
BOYE 2½ = 40 F1 = 38 Y1 = CC
BOYE 6 or 16 = 15 x 1 = AA I thiiiiink. Joe |
Miriam,
What, no guess on what I did to the 500? Joe |
I just thought I would post this, if anyone is close to this location.
http://sfbay.craigslist.org/pen/zip/3403325601.html |
Originally Posted by J Miller
(Post 5661615)
Miriam,
What, no guess on what I did to the 500? Joe |
.............. which spring?
Joe |
Originally Posted by J Miller
(Post 5659473)
http://i119.photobucket.com/albums/o...cs/Front-5.jpg
Alright the problem is solved and it was none of the above. But in trying to diagnose the problems I did the following: Took apart the top tension assembly and cleaned it. Didn't have to, it wasn't the problem, but it never hurts. Cleaned the bobbin case and hook assembly again. I went hunting for a couple pics someone here on the forum emailed me of how to assemble the later top tensions. I didn't find it but I found out I had a 500 manual on my thumb drive. So I checked it out and found I had missed a complete step in threading the top end. I printed the page I needed then stood in front of our 401A while I double checked my assembly of the top tension. Went back downstairs put the tension unit in and rethreaded it correctly. Then I tried to sew and it made it a whole 3" then crunch and broke the thread. Over and over again my wife and I (she finally got in on the act) worked with the tensions, bobbin, and cleaning trying to find out what the heck it's problem was. Then it went crunch and just stopped. Rather than go again and break the thread I carefully removed the needle and needle plate to see where the jam up was. Well, the thread was wrapped around the bobbin case and then around the case support on the back side where the case sits. This didn't make sense at all. It was about then that I realized the bobbin case and hook assembly and the springy thing that holds the bobbin case in was the same as the 401A. So I went upstairs again and opened up the 401A and studied it. Hmmmmmmmm. Back downstairs to the 500. Make one adjustment and zoom zooom we're sewing. No broken threads, ZZ works, stitch patterns work, and I'm thrilled. I had to go back upstairs to get a slant shank special purpose foot to really try some patterns and when I did, the old lady made a few really nice stitches. http://i119.photobucket.com/albums/o...500sewsnow.jpg Now, I'm gonna post a pic of the bobbin area and let you all try and figure out what I had to adjust to fix the problem. http://i119.photobucket.com/albums/o...00bobinfix.jpg Joe Nancy |
| All times are GMT -8. The time now is 02:19 PM. |