Singer 500 hinge pins
#1
Senior Member
Thread Starter
Join Date: Nov 2011
Location: Cary, NC
Posts: 383
Singer 500 hinge pins
I recently bought yet another Rocketeer. Actually, I found it on Craigslist and when we went to look at it, my wife bought it for me for Father's Day. This one had the left-hand side door (sometimes called the nose door, I guess it's the nose cone on the rocket) separate from the machine. The hinges on the door and the machine were intact, the pins were broken off.
The lower broken pin was still inside the hinge on the machine. And at first, I couldn't figure out how to remove it. Luckily, I found a way to remove the lower pin in the service manual at the Yahoo Singer Slant group. When I removed it, I used a small finishing nail to push it out.
I had planned to either order a set of pins or try to find a suitable replacement tomorrow at a hardware store or auto parts shop. However, I had a little brainstorm. The finishing nail's head was just barely larger than the hole in the hinge. I cut the nail short and gently tapped it into place with another nail. I was gentle because I didn't want to accidentally expand the hinge too much and have it crack. I also cut the nails shorter than I think the original pins were so I could lift the door out if I ever want to do so.
It works quite well and I thought I would post this on here for anyone else who has had this problem. The finishing nail is size 4D. The brand I used is, I think, out of business, so be careful using other finishing nails, their heads may be a bit larger. I'll post a photo of the repaired door and the nails, I hope you will be able to see the nails in the door hinges.
By the way, I've heard it speculated that sometimes the nose door gets broken by people trying to lift their machines out of the cabinet by grabbing the left-hand end. Then the door swings open and - snap!
Tate
[ATTACH=CONFIG]480296[/ATTACH]
The lower broken pin was still inside the hinge on the machine. And at first, I couldn't figure out how to remove it. Luckily, I found a way to remove the lower pin in the service manual at the Yahoo Singer Slant group. When I removed it, I used a small finishing nail to push it out.
I had planned to either order a set of pins or try to find a suitable replacement tomorrow at a hardware store or auto parts shop. However, I had a little brainstorm. The finishing nail's head was just barely larger than the hole in the hinge. I cut the nail short and gently tapped it into place with another nail. I was gentle because I didn't want to accidentally expand the hinge too much and have it crack. I also cut the nails shorter than I think the original pins were so I could lift the door out if I ever want to do so.
It works quite well and I thought I would post this on here for anyone else who has had this problem. The finishing nail is size 4D. The brand I used is, I think, out of business, so be careful using other finishing nails, their heads may be a bit larger. I'll post a photo of the repaired door and the nails, I hope you will be able to see the nails in the door hinges.
By the way, I've heard it speculated that sometimes the nose door gets broken by people trying to lift their machines out of the cabinet by grabbing the left-hand end. Then the door swings open and - snap!
Tate
[ATTACH=CONFIG]480296[/ATTACH]
#7
Super Member
Join Date: Oct 2013
Location: Centralia, WA, USA
Posts: 4,890
IIRC the Touch & Sew machines are the same way. You can lift them up and out.
Good solution.
My only comment is to use caution and make sure the replacement pin is the correct diameter or you can break the door when you put the new pin in.
Rodney
Good solution.
My only comment is to use caution and make sure the replacement pin is the correct diameter or you can break the door when you put the new pin in.
Rodney
#8
Power Poster
Join Date: Mar 2011
Location: Somewhere
Posts: 15,507
A pin is one thing those little hinge holes are hard to repair.
Thread
Thread Starter
Forum
Replies
Last Post
amcatanzaro
For Vintage & Antique Machine Enthusiasts
7
07-10-2014 05:39 AM