AlvaStitcher

I just purchased this Singer 66 in a cabinet for $50. I hope I got a good deal. I have already removed the scrolled face cover (not sure that is the proper name) and the needle bar parts. It needs a good cleaning and I am not sure exactly which product to use on which parts. All the metal parts need polishing to restore their shine. The black surface is in pretty good shape with a little grazing on the bed. Any help is appreciated in getting this back to working order again. The needle bar would not go all the way down but I found a piece of thread caught up inside and now it makes a full rotation. Yay![ATTACH=CONFIG]612355[/ATTACH][ATTACH=CONFIG]612356[/ATTACH][ATTACH=CONFIG]612357[/ATTACH][ATTACH=CONFIG]612358[/ATTACH][ATTACH=CONFIG]612359[/ATTACH]
as you can see it has had a stitch regulator added after manufacture. Is it possible to now restore it to using the knob? As i am taking parts off I put them into zipper lock bags with labeling so I go where to put them back. I took the rubber wheel off the bobbin winder as it was shot. Need to order a new one and possibly a new motor pulley belt.

leonf

Beautiful machine. You did well. I would like to suggest taking lots of pictures as you take it apart. Oil everything that moves of should move. Now that you have the access plates open you can reach many things with your oil.

The stitch regulator drew my eye instantly. Way cool. I would leave it on just because it is so rare. and reverse really is a nice feature.

quilterpurpledog

I have a Singer 66 and it is truly "my treasure". I have it in my front entry hall and I enjoy telling people about it. I have documentation for it back to 1906. I paid a whole lot more for it than you did; it was in pristine condition.

WIChix

Lizzie Lenard has a great method to clean up the needle bar and presser bar. Take an 18" thick cotton string, dab a bit of metal polish at the halfway point, thread one end around the bar, bring to front and cross the string ends. Pulling back and forth, moving it up and down, will get the bars cleans.

I would caution you not to remove too many parts. I took way too many parts off of a frozen Singer 128 laVendedora, then decided I probably wouldn't get it back together. Turns out oil, time, more oil, and possibly heat would have been enough to get it moving again. Still sad about that one.

Metal polish is also good for the face and inspection plates, even the Singer badge. Just be careful not to smear it on the decals or black finish.

And yes, I would leave that Revco reverser on. Its a bit of a process to install one, much less remove it and find the missing stitch length screw.

AlvaStitcher

Other question....I have attached a picture of the motor. Do i need to add anything under the screw on top. I know there is a spring under the screw but i don’t min ow if it needs oil or lubricant. Also it looks like oil holes on either end of the motor. Is that correct? Thank you. [ATTACH=CONFIG]612386[/ATTACH]

Mickey2

For they shiny metal bits I find pastes does a better job than liqids, there are lots to choose from; Quick-Glo clean and shines with out being smelly, that's just one of two or three I keep in the cupboard under the sink.

You can reverse the Revco addition, but I think you need to track down the missing parts, I remember at least two previous posters who found the Revco additon to be a bit noisy compared to the original setup.

I'm not sure about the motor, it's a bit different from my Singers, but there might be a carbon brush under the black bakelite screw. There is a motor axle carried by two bearings on each side, and it shows as the protruding point at each end of the motor. The bearings usually takes grease, but on some models it can be one or two drops of oil.

LoriH58

WIChix.. "I took way too many parts off of a frozen Singer 128 laVendedora, then decided I probably wouldn't get it back together. Turns out oil, time, more oil, and possibly heat would have been enough"

I learned about oil-patience-heat and the wonders it does. Great advise. Slow and steady wins the race these days. Oil/Wait/Test. Oil/Wait/Test. Heat as needed.

Where are you in Wisconsin??

luvstoquilt

OMG! I love your new machine!❤️

SusieQOH

That's a beauty! In my opinion $50 is a steal!!!

leonf

Quote

I know there is a spring under the screw but i don’t know if it needs oil or lubricant Quote



nonononononoonononononono
Micky 2 is correct as far as she went. That is access for a brush. You will find another under it for the second brush.

They can be cleaned but not oiled.