Help me get the wonk out of this fabric
#1
Super Member
Thread Starter
Join Date: Jan 2011
Location: Knot Merrill, Southern Indiana
Posts: 5,781
Help me get the wonk out of this fabric
I am going to make a fractured quilt. To do it, I need 4 identical fabric motifs, in my case I'm using a panel. Similar to a stack-and-whack or an OBW, the fabric design has to match (ie large blue flower in exactly the same place on all 4 pieces of fabric when laid on top of each other).
My problem is that the panels are ALL wonky. They're square at the top, but around the middle they all start veering off toward the right. There is no way I could cut strips out of them and match the strips.
The fabric is pre-washed & dried. I then starched it and ironed it (I ironed lengthwise with the selvage only).
I tried stretching them on the bias to get them back into shape and an hour later they're wonky again.
I tried to match sections and put a single stitch in that section and tying it, but I'm getting great big puckers everywhere.
Any suggestions??
My problem is that the panels are ALL wonky. They're square at the top, but around the middle they all start veering off toward the right. There is no way I could cut strips out of them and match the strips.
The fabric is pre-washed & dried. I then starched it and ironed it (I ironed lengthwise with the selvage only).
I tried stretching them on the bias to get them back into shape and an hour later they're wonky again.
I tried to match sections and put a single stitch in that section and tying it, but I'm getting great big puckers everywhere.
Any suggestions??
#2
Super Member
Join Date: Sep 2011
Location: Washington
Posts: 4,001
Boy, I don't have any, it sounds like you are going to be out of luck using that fabric. If it isn't on the straight of grain or if it is not printed properly for the straight of grain, I don't know how you can fix that. Good luck though, I hope someone can help you out.
#3
If you've tried the bias stretch thing and it comes back wonky I'd say ditch it and use a different fabric. It might come back and haunt you specially for what you're planning. You can always find a different project for the panel. JMHO.
#4
Power Poster
Join Date: Feb 2009
Location: Northern Michigan
Posts: 12,861
start in the center---line up the designs---pinning them together so the match perfectly- then smooth the fabric out from them--your outter edges will have to be re-straightened-but your motifs should be lined up- problem with using panals is they are seldom printed exactly alike- and once fabrics have been pre-washed the wonky-ness really becomes apparent- in some cases it is better to forgo the prewashing part---but too late now- the only thing to do is line up the designs---but it may still be impossible-they may not even be the same size anymore- putting them together and pinning them will show you if their size is off too.
good luck.
good luck.
#6
Have you tried wetting the fabric and pinning it to something to block it? Sort of like you would with knitting or crocheting. Wet it, roll it in a towel to partially dry it then pin it to something sturdy or tape it to your vinyl floor (making sure it's straight) and leave it there until it's TOTALLY dried.
#7
Yes, I'd try what Raptureready suggests. If you have an ironing board cover with a measuring tape cover, it would be even easier. Lay and straighten the first damp one and pin down very well. Then position, straighten, stretch as needed, the second on top of it and pin, and so on. Remember that wet fabric will stretch very easily. Try it with one set of 4 squares and see what happens.
I had a baby panel that had a terrible WOW in the middle and this technique worked for me.
I had a baby panel that had a terrible WOW in the middle and this technique worked for me.
#8
Power Poster
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,538
Do you have a ruler big enough to cut the pieces you need in one cut? If you do, lay your ruler over the motif you want to cut. Put Glad Press & Seal over the whole ruler top. Use a fine sharpie and exactly trace the motif on the glad plastic and this creates a template for cutting exact matching sections. Then cut out your sections one at a time. You will get the exact repeats but you would still have to tape the wonky sections to your cutting mat to get straight lines to sew? I don't know if it will work on your wonky panels but do a dry run with one panel and see before cutting anything. As others have said you may need to change your fabric choice.
Thread
Thread Starter
Forum
Replies
Last Post
mpeters1200
Main
21
09-09-2008 06:44 AM