How do I use a hemmer foot?
#11
here is another she really knows how to use it I could never master mine https://www.youtube.com/watch?v=vpzj0Cu5zog
#12
I have used a rolled hemming foot with success. The trick is getting it started. You start out by folding a narrow hem (1/8") over twice. You only need to do this for half inch or so. It helps to touch a hot iron to it to hold it in place. Then take it to your machine and put the needle down through the hem. Next take the fabric and pull it up through the rolled part of the foot and start stitching. The rolled part of the foot will roll the fabric into a narrow hem and the needle which follows closely behind will stitch it in place. You don't have to worry too much about where the needle will fall on the fabric because the foot will guide it. To do corners I stitch to the end and then start the new side fresh like I started out but try to miter the corner on the new side a bit to make it neater. I tried going around a gentle curve and it did not work well. I was able to do it but got some rippling. Straight edges work better. My manual for my machine (Janome 8900) had some instructions and pictures. If your's doesn't perhaps there is a tutorial you could watch on line. I love having that foot for finishing things off like napkins and such. It is a very narrow hem so wouldn't use it much for garment construction.
The real trick that worked for me is holding the fabric up away from the bed of the machine to allow the roll in the foot to be able to take it up.
The real trick that worked for me is holding the fabric up away from the bed of the machine to allow the roll in the foot to be able to take it up.
#13
Super Member
Join Date: Sep 2010
Location: Live Oak, Texas
Posts: 6,133
I have two types of hemmer feet, one is for blind stitching and is for a wider hem and one for a small rolled hem that would be used for a ruffle. The instruction book that came with your machine will show you how to use both.
#15
Senior Member
Thread Starter
Join Date: Feb 2012
Posts: 673
I guess I didn't word my question correctly. What seemed obvious to me (that I looked up instructions and videos in as many places as possible before submitting my question) was not an assumption shared by others. I guess my question should have been: Have you used the hemmer foot successfully? What tricks or techniques do you use?
I was surprised to see on the Singer web site a recommendation that a narrow, double-folded hem be ironed the entire length of the piece to be hemmed before using the foot. At that point a regular straight-stitch foot would work almost as well, I would think. The fabric I'm working with is a mystery fiber, but its resistance to ironing tells me the polyester content is significant. Attempting to iron a 1/8" hem several feet long (it's for curtains) with this fabric would send me either to the liquor store or the loony bin. I've practiced (quite a bit) with scraps of the fabric and have gotten some flawless stretches of hem (the fabric seems to be the right weight for this technique), after which it misbehaves (I can't see that I'm doing anything differently) and then it's single folded, pleated lengthwise, twisted, sloppy, etc. One video showed the person demonstrating holding the feed fabric sharply to the left, another put slight tension on the fabric by holding it front and back, and so on. I mimicked all these methods as best as I could and results were inconsistent.
I was surprised to see on the Singer web site a recommendation that a narrow, double-folded hem be ironed the entire length of the piece to be hemmed before using the foot. At that point a regular straight-stitch foot would work almost as well, I would think. The fabric I'm working with is a mystery fiber, but its resistance to ironing tells me the polyester content is significant. Attempting to iron a 1/8" hem several feet long (it's for curtains) with this fabric would send me either to the liquor store or the loony bin. I've practiced (quite a bit) with scraps of the fabric and have gotten some flawless stretches of hem (the fabric seems to be the right weight for this technique), after which it misbehaves (I can't see that I'm doing anything differently) and then it's single folded, pleated lengthwise, twisted, sloppy, etc. One video showed the person demonstrating holding the feed fabric sharply to the left, another put slight tension on the fabric by holding it front and back, and so on. I mimicked all these methods as best as I could and results were inconsistent.
Last edited by Manalto; 10-10-2015 at 02:06 PM.
#16
Senior Member
Join Date: Jun 2011
Location: Cedar Falls, IA
Posts: 923
The Bernina website has nice videos of how to use a hemming foot (applies to all machines). I prefer the method where you start sewing a few stitches, remove the fabric gently, and then start rolling the hem. I finally have the foot mostly mastered, but it takes a lot of concentration to keep it evenly curled.Pam
#20
Senior Member
Thread Starter
Join Date: Feb 2012
Posts: 673
UPDATE: I did this the easiest way possible - took it to someone else to do! The more I tried and failed with the narrow hemming foot and the more I thought about struggling with seven pairs of curtains with generous lengths of ruffle, the less appealing the job sounded. There's a shop not far away with an excellent reputation that agreed to do it for a fair price. (I had to wait a couple of weeks before she could get to it, hence my delay with the update.) When I brought in the fabric, I explained why I wasn't doing it myself. The tailor (seamstress? What's the proper term?) said she's been sewing for more than 30 years and she could never get that foot to work properly. ("Maybe I'm just impatient." she added.) I asked her how she did the narrow turn required for a ruffle and she described the technique in Prism99's post below. So, a belated thank you. (How do we know which suggestion is the right one for us when there are so many options?)
Curious about this method (and an inveterate glutton for punishment) I bought some more similar fabric and am in the midst of making a couple pairs of this style of curtain for the two kitchen windows in my house. The stitch-close-to-the-edge narrow hem technique is slow going, but so far, so good.
What I have done in the past (alas, many years ago!) was to stitch a line 1/4" from the edge, take to ironing board and iron the fabric along that line (just barely hiding the stitching underneath), then turn the edge again and iron, then take back to the sewing machine to stitch the double turn down. The first row of stitching becomes hidden in the hem. It sounds like more work than using a hemming foot, but for me it ended up taking a lot less time as I was never able to master the hemming foot for a neat result.
Last edited by Manalto; 10-17-2015 at 10:55 AM.
Thread
Thread Starter
Forum
Replies
Last Post
Snooze2978
General Chit-Chat (non-quilting talk)
20
04-06-2015 06:11 PM
baywinds
For Vintage & Antique Machine Enthusiasts
1
06-20-2013 11:32 AM
cvthedragonlady
For Vintage & Antique Machine Enthusiasts
1
03-24-2012 12:35 AM