Borders greater or less than 90 degrees - help
#1
Senior Member
Thread Starter
Join Date: May 2007
Location: San Bruno, CA
Posts: 433
Borders greater or less than 90 degrees - help
I am making the Butterfly Jungle Table Runner from free patterns.com
https://www.freepatterns.com/detail....342&cat_id=434
I am having problems sewing the borders on with the mitered corners. I get as far as figure 5, but can not do figure 6 or 7. Can you offer any help?
https://www.freepatterns.com/detail....342&cat_id=434
I am having problems sewing the borders on with the mitered corners. I get as far as figure 5, but can not do figure 6 or 7. Can you offer any help?
#2
Super Member
Join Date: Jun 2010
Location: The Deep South near Cajun Country, USA
Posts: 5,434
This pdf file provided by Anka's Treasures might help you.
https://ankastreasures.wordpress.com...ng-odd-angles/
https://ankastreasures.wordpress.com...ng-odd-angles/
#4
I'm not going to sign up to their site for the download, but from the image it appears that the corners are 90 degrees at the ends and 125 degrees on the sides. That means that the miters are half that size, 45 degrees at the ends and 62.5 degrees at the sides.
#6
Super Member
Join Date: Jul 2010
Posts: 1,029
What I have always done (even for the 90 degrees) is to sew both seams up to the 1/4 inch seam allowance with extra fabric hanging over (unsewn)... Then I turn the quilt to right side up and leave one straight/flat and use the top one and fold it to meet the other on the outside. In a 90 degree miter this is a 45 degree line. But I don't see why it wouldn't work for a differing degree change. You can basically line up the two points to create that line (and not really worry about degrees)
I then press it very well so I can see the line well. Gently open the top piece while keeping the bottom still and in place. Then I pin across the seam from the outer point to the inner. And sew....
Hope this helps!
I then press it very well so I can see the line well. Gently open the top piece while keeping the bottom still and in place. Then I pin across the seam from the outer point to the inner. And sew....
Hope this helps!
#7
Super Member
Join Date: Jul 2010
Location: Glenmoore, PA
Posts: 7,941
What I have always done (even for the 90 degrees) is to sew both seams up to the 1/4 inch seam allowance with extra fabric hanging over (unsewn)... Then I turn the quilt to right side up and leave one straight/flat and use the top one and fold it to meet the other on the outside. In a 90 degree miter this is a 45 degree line. But I don't see why it wouldn't work for a differing degree change. You can basically line up the two points to create that line (and not really worry about degrees)
I then press it very well so I can see the line well. Gently open the top piece while keeping the bottom still and in place. Then I pin across the seam from the outer point to the inner. And sew....
Hope this helps!
I then press it very well so I can see the line well. Gently open the top piece while keeping the bottom still and in place. Then I pin across the seam from the outer point to the inner. And sew....
Hope this helps!
#8
Super Member
Join Date: Jun 2011
Location: Illinois
Posts: 9,018
You sew the strip to the main straight, trimming to meet the line of the piece gives you the angle you need...you don't cut the strip at the angle then try to match it......there must be a tute somewhere...it's easier done than said....
Thread
Thread Starter
Forum
Replies
Last Post
Hosta
General Chit-Chat (non-quilting talk)
4
02-17-2011 08:34 AM