Trisher

Dec La Table runner (kit from Connecting Threads) is done. I am happy with it, except for the glue that oozed out from under the ribbons and is very visible. I know... I am way too generous with glue! Any suggestions? I have tried freezing and then trying to pick off, without success.

[ATTACH=CONFIG]449598[/ATTACH]

hatchet

I don't know, would a paper bag and an iron work? It's real pretty as is, might want to just leave it...

RuthFru

Did you try using warm water. I would try just using the warm water on a clean cloth and gently rub.

tessagin

You could try dipping a q-tip in some Goo Be Gone and see if that helps. Love your table top!

RedGarnet222

Lovely runner! It looks so at home in your dining room.

I downloaded this about three weeks ago and haven't had the time to make it as yet. I will be extra careful with any glue that is supposed to be used. Thanks for the heads up.

Prism99

What kind of glue did you use? If it was Elmer's white washable school glue, I second dipping a cloth in water and rubbing gently. Do allow the water a little time to penetrate the glue. Experiment on a sample first if you are unsure. (A toothpick might help too.)

Trisher

When all else fails... look up the manufacturer's instructions.... Duh

"

[TABLE]
[TR]
[TD="colspan: 2"]REMOVING FABRI-TAC FROM FABRICS[/TD]
[/TR]
[TR]
[TD][/TD]
[TD="width: 3"][/TD]
[TD="colspan: 2"]The best way to remove FABRI-TAC from most fabrics is by dry cleaning. Sometimes, however, this is not possible. Our loyal customers who have been using and loving Fabri-Tac for years, have suggested the following method. The best advice is to BE PATIENT while doing this process.
How long it will take to effectively remove the glue depends upon how much you are removing.
[/TD]
[/TR]
[TR]
[TD="width: 150"][/TD]
[TD="width: 3"]•[/TD]
[TD="colspan: 2"]SUPPLIES YOU’LL NEED
1. Spoon or butter knif
2. Acetone
3. Clean rag[/TD]
[/TR]
[TR]
[TD="width: 150"][/TD]
[TD="width: 3"]•[/TD]
[TD="colspan: 2"]BEFORE STARTING
1. ALWAYS test first on a small, unseen area of the item to ensure that the acetone will not discolor or adversely affect the fabric.
2. NEVER use a dining room table or any finished surface as a work area as acetone will strip off the finish. Cover your work area with plastic or newspaper.[/TD]
[/TR]
[TR]
[TD="width: 150"][/TD]
[TD="width: 3"]•[/TD]
[TD="colspan: 2"]BE CAREFULL!
1. Acetone is a FLAMMABLE solvent and should always be kept away from heat, open flames, lighted cigarettes, and other sources of ignition.
2. Keep acetone out of reach of children.
3. Wear eye protection.
4. Work in a well ventilated area[/TD]
[/TR]
[TR]
[TD="width: 150"][/TD]
[TD="width: 3"]•[/TD]
[TD="colspan: 2"]REMOVING FABRI-TAC
Step 1: Remove of much of the dried Fabri-Tac as you can by using your fingernail, a spoon or butter knife.
Step 2: Wet a small portion of the rag with acetone. Slowly rub the wet rag directly onto the adhesive to be removed. Wet & turn the rag often to keep it from drying out.
Step 3: The wet rag will soften & liquefy the glue. This will be a slow process. Gently peel off any blobs of glue you see and discard.[/TD]
[/TR]
[TR]
[TD="width: 150"][/TD]
[TD="width: 3"]•[/TD]
[TD="colspan: 2"]DO NOT DIP THE GARMENT OR FABRIC INTO THE ACETONE! This will make the glue more difficult to remove and may permanently damage the fabric!
Some individuals may be sensitive to acetone’s smell. If you or anyone near you dislikes the smell, immediately discontinue the removal process[/TD]
[/TR]
[TR]
[TD="width: 150"][/TD]
[TD="width: 3"][/TD]
[TD="colspan: 2"]CUSTOMER SERVICE: Signature Crafts, 1-800-865-7238[/TD]
[/TR]
[/TABLE]

GrammaNan

The table runner is beautiful.

MacThayer

Good for you for looking up the manufacturer's instructions! It amazes me how often I fail to think of that. Think I'll put it on a card and pin it to my cork board. LOL!

Trisher

Then you have to remember to LOOK at your cork board!