FMQ-Vintage Machine Settings?
#1
I just bought a Singer 15-91 to do my FMQ on. I am new to FMQ. I've been doing it on my newer little Brother SE-350. I'm hoping it will be easier on the vintage Singer. I love the way the Singer sews, but I am having a little trouble with the settings when I FMQ on the Singer. The upper thread breaks occasionally. I am not using machine quilt thread, would that make a big difference? Any tips on tension and stitch settings?
#2
First, you set the bobbin tension so that it's right for the thread that you want to use in the bobbin, then you use the right size needle for the thread and balance the upper tension with the bobbin thread tension.
If the bobbin tension is set correctly, you will be able to put the bobbin in and thread it and pick it up by the thread. If you can't do this without the thread unwinding freely, set the tension screw on the bobbin case a quarter-turn tighter at a time until you can pick up the bobbin case by the thread.
Now, a little jerk on the thread (like you're swinging a tiny yo-yo) should make the bobbin case slide down the thread a little ways and stop. If it doesn't slide at all, loosen the tension screw a few degrees at a time until it does.
Now, replace the bobbin and set the upper tension so that when you sew a sample similar to what you want to do the free-motion quilting one, the threads are balanced top and underside, with the twist occurring inside the quilt sandwich.
If there are big loops on the underside of the fabric, the upper tension is too loose. If the needle thread lies in a flat line with loops of the bobbin thread hooked over it, the upper tension is too tight.
If your needle thread is breaking occasionally, it could be just the way that you were handling the fabric for a few seconds.
But, if the needle thread breaks often, the eye of the needle is probably too small for the thread - change to a large-eye needle in the same size, or go up one size at a time until you find the one that works with your upper thread.
One of the beautiful things about the 15 is that it is very adaptable - it will sew just about anything. I've used a super-fine bobbin thread with size 30 or 40 embroidery threads - beautiful stitches! :) You don't have to match the threads, you just have to set the bobbin tension correctly for the thread you want to use, use the right size needle for the upper thread, and balance the upper tension with the lower.
The feed dogs are dropped, so the stitch settings don't mean anything.
This will all be second nature to you in about a day or two. Good luck and have fun! :)
If the bobbin tension is set correctly, you will be able to put the bobbin in and thread it and pick it up by the thread. If you can't do this without the thread unwinding freely, set the tension screw on the bobbin case a quarter-turn tighter at a time until you can pick up the bobbin case by the thread.
Now, a little jerk on the thread (like you're swinging a tiny yo-yo) should make the bobbin case slide down the thread a little ways and stop. If it doesn't slide at all, loosen the tension screw a few degrees at a time until it does.
Now, replace the bobbin and set the upper tension so that when you sew a sample similar to what you want to do the free-motion quilting one, the threads are balanced top and underside, with the twist occurring inside the quilt sandwich.
If there are big loops on the underside of the fabric, the upper tension is too loose. If the needle thread lies in a flat line with loops of the bobbin thread hooked over it, the upper tension is too tight.
If your needle thread is breaking occasionally, it could be just the way that you were handling the fabric for a few seconds.
But, if the needle thread breaks often, the eye of the needle is probably too small for the thread - change to a large-eye needle in the same size, or go up one size at a time until you find the one that works with your upper thread.
One of the beautiful things about the 15 is that it is very adaptable - it will sew just about anything. I've used a super-fine bobbin thread with size 30 or 40 embroidery threads - beautiful stitches! :) You don't have to match the threads, you just have to set the bobbin tension correctly for the thread you want to use, use the right size needle for the upper thread, and balance the upper tension with the lower.
The feed dogs are dropped, so the stitch settings don't mean anything.
This will all be second nature to you in about a day or two. Good luck and have fun! :)
#5
I played around a little more today, and it was better. Thread not breaking, but I am getting extra long stitches every now and then. I assume it's me not in sync yet. I love it so far! I have a litte scrappy table runner I think I'll practice on today.
#6
Good going!
It was really crazy for me at first - sooooo hard! And even now, sometimes I can't figure out which way I need to go next - that's when I know I haven't doodled the design enough on the dry erase board. When you get to where you can draw the design without even thinking of where to go next, you will be amazed when you sit down to the machine - the designs seem to come out of the needle all by themselves. :)
I still can't keep my stitches the same length, though.
Someday, I'll have a stitch regulator that's a little more reliable than the one between my ears! :lol:
It was really crazy for me at first - sooooo hard! And even now, sometimes I can't figure out which way I need to go next - that's when I know I haven't doodled the design enough on the dry erase board. When you get to where you can draw the design without even thinking of where to go next, you will be amazed when you sit down to the machine - the designs seem to come out of the needle all by themselves. :)
I still can't keep my stitches the same length, though.
Someday, I'll have a stitch regulator that's a little more reliable than the one between my ears! :lol:
Thread
Thread Starter
Forum
Replies
Last Post
Lystra
Links and Resources
37
09-18-2011 09:11 PM