If your ruler has been used a lot - - -
#1
Power Poster
Thread Starter
Join Date: May 2008
Location: MN
Posts: 24,646
If your ruler has been used a lot - - -
ube quilting mentioned on this thread
http://www.quiltingboard.com/main-f1...e-t288400.html
about her ruler getting worn down and then her strips had a curve in them.
I have had this happen with my rulers, too.
It took me a while to figure out why - when I moved my ruler - and had not moved the fabric - why the edge of the fabric was not "straight" on the measuring line.
Turns out that i had worn a curve into the edge of the ruler. When I finally set it on a straight surface - like my kitchen counter - I could see that my ruler was making a shallow arch.
Of course it caused me pain to discard the ruler - but it caused me more pain to have wonky strips.
http://www.quiltingboard.com/main-f1...e-t288400.html
about her ruler getting worn down and then her strips had a curve in them.
I have had this happen with my rulers, too.
It took me a while to figure out why - when I moved my ruler - and had not moved the fabric - why the edge of the fabric was not "straight" on the measuring line.
Turns out that i had worn a curve into the edge of the ruler. When I finally set it on a straight surface - like my kitchen counter - I could see that my ruler was making a shallow arch.
Of course it caused me pain to discard the ruler - but it caused me more pain to have wonky strips.
#5
Super Member
Join Date: Jan 2012
Posts: 4,783
Wow, I would never have expected to have that happen.
I did noticeably wear out the starting corner on one of my rulers. So now when using the rotary cutter I don't begin at the end of the ruler (and slice off the corner). Instead I begin ahead of the corner a bit, roll backwards just to the end of the ruler, then forward with the cut.
I did noticeably wear out the starting corner on one of my rulers. So now when using the rotary cutter I don't begin at the end of the ruler (and slice off the corner). Instead I begin ahead of the corner a bit, roll backwards just to the end of the ruler, then forward with the cut.
#7
Super Member
Join Date: Apr 2016
Location: Blue Ridge Mountians
Posts: 7,075
Wow, I would never have expected to have that happen.
I did noticeably wear out the starting corner on one of my rulers. So now when using the rotary cutter I don't begin at the end of the ruler (and slice off the corner). Instead I begin ahead of the corner a bit, roll backwards just to the end of the ruler, then forward with the cut.
I did noticeably wear out the starting corner on one of my rulers. So now when using the rotary cutter I don't begin at the end of the ruler (and slice off the corner). Instead I begin ahead of the corner a bit, roll backwards just to the end of the ruler, then forward with the cut.
#9
Power Poster
Join Date: Jan 2011
Location: Southern USA
Posts: 16,398
Wow, I would never have expected to have that happen.
I did noticeably wear out the starting corner on one of my rulers. So now when using the rotary cutter I don't begin at the end of the ruler (and slice off the corner). Instead I begin ahead of the corner a bit, roll backwards just to the end of the ruler, then forward with the cut.
I did noticeably wear out the starting corner on one of my rulers. So now when using the rotary cutter I don't begin at the end of the ruler (and slice off the corner). Instead I begin ahead of the corner a bit, roll backwards just to the end of the ruler, then forward with the cut.
#10
ube quilting mentioned on this thread
http://www.quiltingboard.com/main-f1...e-t288400.html
about her ruler getting worn down and then her strips had a curve in them.
I have had this happen with my rulers, too.
It took me a while to figure out why - when I moved my ruler - and had not moved the fabric - why the edge of the fabric was not "straight" on the measuring line.
Turns out that i had worn a curve into the edge of the ruler. When I finally set it on a straight surface - like my kitchen counter - I could see that my ruler was making a shallow arch.
Of course it caused me pain to discard the ruler - but it caused me more pain to have wonky strips.
http://www.quiltingboard.com/main-f1...e-t288400.html
about her ruler getting worn down and then her strips had a curve in them.
I have had this happen with my rulers, too.
It took me a while to figure out why - when I moved my ruler - and had not moved the fabric - why the edge of the fabric was not "straight" on the measuring line.
Turns out that i had worn a curve into the edge of the ruler. When I finally set it on a straight surface - like my kitchen counter - I could see that my ruler was making a shallow arch.
Of course it caused me pain to discard the ruler - but it caused me more pain to have wonky strips.
NO NO NO. The other three edges are still good.
Thread
Thread Starter
Forum
Replies
Last Post
bearisgray
Main
31
06-23-2016 08:38 AM
pinkcastle
Main
10
07-07-2012 12:19 PM
lindamar
Main
18
09-20-2011 06:50 AM