Moving the machine, not the fabric
#1
Moving the machine, not the fabric
I've been looking at the Sweet 16 model and those types, but I would really like a machine where you move the machine itself, not the fabric. What are the suggested options, other than a full size long arm?
Thanks, Watson
Thanks, Watson
#2
Power Poster
Join Date: Dec 2008
Location: Western Wisconsin
Posts: 12,930
I have a Voyager 17 with Hinterberg frame, which is more like a midarm than a longarm. For setups where you move the machine, it is really the frame that takes up all the space. I'd have to go measure to be sure, but my frame is about 4 feet deep but you then need at least 3 additional feet at the front for your body. Most people also want 2 to 3 additional feet of space at the back to get around the frame for plugs, working on the machine, and to do pantographs from the back (3 feet). The width of the frame depends on the biggest size quilt you want to be able to mount. Mine is 10 feet wide, and I can fit a quilt up to 9 feet on it (you need to allow at least one foot on one side of the frame so you can put bobbins in the machine.
There are a couple of frames out that are smaller. I've seen questions about them posted recently on the QB. I think one is a Babylock. These are not the usual setup in that you need to layer the quilt as usual and then clamp just portions of the quilt to the frame while you move the machine to quilt.
There are a couple of frames out that are smaller. I've seen questions about them posted recently on the QB. I think one is a Babylock. These are not the usual setup in that you need to layer the quilt as usual and then clamp just portions of the quilt to the frame while you move the machine to quilt.
#4
Super Member
Join Date: Aug 2011
Location: kansas
Posts: 6,407
Yes--there is a big difference in the 2 methods. Is your hesitancy with the full size long arm due to the space or the cost? If it's the cost, you might contact some dealers about a used machine. Space can be awkward, but 12' frame can sometimes but positioned at an angle in bedrooms. good luck with finding a machine that you like and works for you--I absolutely love the quilting process.
#5
Super Member
Join Date: Jun 2010
Location: England Alton Towers
Posts: 6,673
I have a wooden frame on which I use either my janome or juki machines. ( preference to juki which has a larger throat..) it works very well on free motioning a quilt. King and queen size don't fit exactly do them in sections. I use ,red snappers to load quilt and it goes on quick and easy. I already had the janome when I purchased the machine. Purchased juki at a quilt show later. The set up cost about £1000 altogether the wooden frame a few hundred with machine costing about the same. The wooden frame is 9ft which was size for my wall. It did do different sizes.
#8
I have a brother 1500 on a home made frame. Very limited in quilting space, only about 5 inches, but it works for me although at times it feels like driving a truck without power steering as the carriage and frame not the smoothest. I dream of a long arm.
#9
Brother has a 5ft dream fabric frame, very decently sized for small areas and it is compatible with the 14 inch qnique/blockrockit, you can do all size quilts on the frame due to its size. i believe handiquilter also has a similar frame but the brother one looks nicer to me but believe you can use a bigger machine on theirs I think not sure
Thread
Thread Starter
Forum
Replies
Last Post
Smorris17119
For Vintage & Antique Machine Enthusiasts
11
04-02-2014 11:28 AM
MYWR
Offline Events, Announcements, Discussions
25
08-08-2013 04:36 AM
4dogs
For Vintage & Antique Machine Enthusiasts
11
04-30-2012 05:54 AM