Needle reminders
#91
Member
Join Date: Aug 2011
Posts: 3
I have several machines also - I put a color dot on the machines - RED / Green / yellow - that matched pin heads that I had - made a chart on fabric with batting behind it: across the top is the size of the needle (ie 60 - 70 - 80 - 90) and down the side is the type - universal, quilting, topstitch, metallic etc. Then I put the color coded pin in the slot to match the needle in the machine
when I take it out (say metallic) I put it where the pin is on the chart so I can use it again. Hope this helps
when I take it out (say metallic) I put it where the pin is on the chart so I can use it again. Hope this helps
#92
Junior Member
Join Date: Jan 2010
Location: central fl
Posts: 139
I take the needle out of the package and tape with painters tape the package to the front of my machine. I only have one package taped there at any given time and I know what needle is in the machine. I do put a swipe of nail polish on the outside of the package. That is to remind me that that particular needle has been used but still has some "life" left in it.
#96
Super Member
Join Date: Jan 2011
Location: Port Lavaca, TX
Posts: 1,276
Originally Posted by Cindy2sew
Ok, I admit I am getting older (52) and I have difficulty remembering which needle is in my machine! I switch projects a lot and change my needle (when I remember) to the project I am working on so I could end up with an denim needle on a embroidery project. (Its happened)
I need some ideas how to remember which needle I have loaded in my machine. I have tried post-it notes on the front of the machine but I find they fall off too easily. Any suggestions?
Cindy
I need some ideas how to remember which needle I have loaded in my machine. I have tried post-it notes on the front of the machine but I find they fall off too easily. Any suggestions?
Cindy
#97
Member
Join Date: Oct 2009
Location: Bellingham, WA
Posts: 57
I have a gadget I bought several years ago called a Needle Grabbit. It is a heavy magnet covered w/a sheet divided into rectangles with the type of needle in use, i.e., Universal, Stretch, Ballpoint, Denim, Microtex, Quilting and Embroidery with several blank rectangles. You write in the needle size w/marking pen. A small magnet is attached to the board which you use to indicate what size needle you are currently using. For instance, say you use 4 different size universal needles. You would write 100, 80, 90 and 70 in the four universal rectangles. If you are currently using an 80 needle you would place the small magnet in that rectangle to show that's what's in the machine. Wish I could explain it better or take a picture but not that savvy with the computer. This was made by blue-feather.com but many years ago. Don't know if they still make them but you might inquire.
#99
Super Member
Join Date: Dec 2010
Location: Norfolk, VA
Posts: 5,397
Originally Posted by janell2009
I am going to watch this thread... I am 51... do the same thing... yes.. I have had a denim needle in when doing embroidery..... I wish I could figure out a way when I take them out of the package to then identify what they are.. Have bifocals and find it too difficult to read what is on the needle.. I have 2 machines so have to be sure and keep them all straight.. UGH...
I do find the trick using a common drinking straw to help remove and put in new needles... you just hold the drinking straw horizontal and push the needle into one side of the straw. Then it has a handle... it is much easier to put it in and I use that to take it out also, just lay drinking straw on the top of the foot and move needle down by hand and pierce thru one side of straw, loosen the screw.. and it comes out with out dropping into the feed dogs.
I do find the trick using a common drinking straw to help remove and put in new needles... you just hold the drinking straw horizontal and push the needle into one side of the straw. Then it has a handle... it is much easier to put it in and I use that to take it out also, just lay drinking straw on the top of the foot and move needle down by hand and pierce thru one side of straw, loosen the screw.. and it comes out with out dropping into the feed dogs.
Thread
Thread Starter
Forum
Replies
Last Post
grocifer
General Chit-Chat (non-quilting talk)
0
01-01-2012 07:37 AM