Go Back  Quiltingboard Forums >
  • Main
  • Pressing Strip Sets >
  • Pressing Strip Sets

  • Pressing Strip Sets

    Thread Tools
     
    Old 02-03-2013, 12:11 PM
      #1  
    Junior Member
    Thread Starter
     
    Join Date: Jun 2011
    Location: Sacramento
    Posts: 100
    Default Pressing Strip Sets

    Do you have any hints on pressing strip sets? I'm working on six strips in a set and each strip is two and a half inches. I need to press the seams to the sides, and some need to be pressed one way and some the other so they will match when the sets are sewn into blocks. I would like to get a nice, crisp seam every time without pulling and tugging those seams when pressing. More often than not I get a tiny fold of fabric over the seam line. Any advice would be appreciated.

    Also, I'm using a cordless iron on high. It doesn't seem to get as hot as a regular iron. Could that also be part of the problem?
    Rivercity is offline  
    Old 02-03-2013, 12:15 PM
      #2  
    Banned
     
    Join Date: Mar 2010
    Location: Sturbridge, Ma
    Posts: 3,992
    Default

    I first set the seam then on the top run the iron right on the edge of the seam holding one strip up. I don't try to press to the side at this point. This appears to heat the seam. I then go back with the iron and press the seam to the side. This extra step seems to keep those small pleats from forming.
    Holice is offline  
    Old 02-03-2013, 12:19 PM
      #3  
    Power Poster
     
    Join Date: Dec 2010
    Location: Michigan
    Posts: 11,276
    Default

    on long seams like strip sets, I set the seam with the iron, then run my fingernail (or wooden iron) along the seam to start pressing it to the side. Then I follow up with a hot iron. Seems like if I just use my iron, I get little folds.
    PaperPrincess is offline  
    Old 02-03-2013, 12:42 PM
      #4  
    Super Member
     
    needles3thread's Avatar
     
    Join Date: May 2010
    Location: Missouri
    Posts: 3,255
    Default

    There is a tool made for pressing strip sets called The Strip Stick. It comes in 2 different lengths. (45" or 18")
    www.thestripstick.com. made in Texas USA It is a stick with a cloth covered
    curved pressing surface. Hope this helps.
    needles3thread is offline  
    Old 02-03-2013, 01:21 PM
      #5  
    Super Member
     
    Scissor Queen's Avatar
     
    Join Date: Jul 2009
    Location: Southwest Kansas
    Posts: 4,820
    Default

    Originally Posted by needles3thread
    There is a tool made for pressing strip sets called The Strip Stick. It comes in 2 different lengths. (45" or 18")
    www.thestripstick.com. made in Texas USA It is a stick with a cloth covered
    curved pressing surface. Hope this helps.

    I'll second this. You'll get perfectly straight strip sets every time. Plus you can press seams to one side or press them open. Wrong side up presses them open and right side up presses them to one side.
    Scissor Queen is offline  
    Old 02-03-2013, 01:34 PM
      #6  
    Super Member
     
    Join Date: Mar 2010
    Location: Anchorage, AK
    Posts: 1,397
    Default

    I also set my seam then I press from the front to avoid the little creases that can sneak in on me when I iron from the back. If, as usual, I'm pressing to the dark, I put the light down on the board and hold the dark up with my left (non-ironing) hand as I let the seam allowance lay to the side and press carefully - that probably doesn't make sense to any of you...does it?
    ktbb is offline  
    Old 02-03-2013, 01:34 PM
      #7  
    Super Member
     
    Join Date: Jul 2010
    Location: Ohio
    Posts: 2,148
    Default

    When pressing strip sets I always press to the same side ( ususally darker) on each set. This seems to allow the seams to be alternate ways when sewing blocks together. Also I set the seam by lightly pressing seam closed before pressing to one side. I just did 20+ set and this pressing worked ever time.
    bigsister63 is offline  
    Old 02-03-2013, 01:39 PM
      #8  
    Power Poster
     
    Join Date: Dec 2008
    Location: Western Wisconsin
    Posts: 12,930
    Default

    I third the StripStick. If you cannot afford it, look for unfinished half-round molding in a hardware store (not all places have it; you do *not* want three-quarter's round). You don't even have to cover it with fabric (the StripStick is covered with muslin). Works great for keeping the seams straight, and you can press either to the side or open.

    Here's a link to the type of wood you would need:
    http://www.homedepot.com/buy/america...l#.UQ7Y2h3hq0I
    Prism99 is offline  
    Old 02-03-2013, 03:22 PM
      #9  
    Super Member
     
    franc36's Avatar
     
    Join Date: Dec 2010
    Location: Tennessee
    Posts: 1,501
    Default

    Thanks to all of you for your suggestions. I am going to make strip sets tomorrow. Now I feel better about pressing them. Thanks!!!
    franc36 is offline  
    Old 02-03-2013, 04:00 PM
      #10  
    Super Member
     
    Join Date: Aug 2010
    Location: Piedmont Virginia in the Foothills of the Blue Ridge Mtns.
    Posts: 8,562
    Default

    I press from the front (right side) of the strip set, pressing toward the upper strip with the point of the iron. Then I go back over the set with the iron making sure there are no tiny folds along the seam line.

    Jan in VA
    Attached Thumbnails pressing-seam-open.png  
    Jan in VA is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    Buckeye Rose
    Main
    28
    10-12-2012 04:11 AM
    Barb_MO
    Main
    16
    04-25-2010 05:14 PM
    Joan in AK
    Main
    7
    02-09-2010 01:17 PM
    sondray
    Links and Resources
    5
    11-19-2008 11:53 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is On
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter