Question from a beginnner quilter
#11
Super Member
Join Date: Sep 2011
Location: West Texas
Posts: 2,073
Tina,
Try a seam with your walking foot and then measure it to see if it is a 1/4".
I am not sure that I would use a walking foot for all my piecing -- it runs a lot slower than I would like, and since it has moving parts, it will wear. However, it will help with matching seams, especially on long runs. You may find that it is the perfect solution.
Dayle
Try a seam with your walking foot and then measure it to see if it is a 1/4".
I am not sure that I would use a walking foot for all my piecing -- it runs a lot slower than I would like, and since it has moving parts, it will wear. However, it will help with matching seams, especially on long runs. You may find that it is the perfect solution.
Dayle
#12
Member
Thread Starter
Join Date: Nov 2012
Location: Wales, UK
Posts: 58
Okay, taking on board your advice, I thought I would treat myself to a 1/4" foot for my machine, especially as the walking foot was very expensive and I don't want to wear it out. Now the only problem seems to be that they don't make one for my machine , it's an Elna 2300.
#13
The Walking Foot was originally known as the Matching Foot. It matched seams of plaid and directional fabric. I use it for piecing all the time. My seams match without any problem and I sew slower. I always keep an eye out for used feet that fit my machine. I have several of the ones I use a lot.
#14
Member
Thread Starter
Join Date: Nov 2012
Location: Wales, UK
Posts: 58
The Walking Foot was originally known as the Matching Foot. It matched seams of plaid and directional fabric. I use it for piecing all the time. My seams match without any problem and I sew slower. I always keep an eye out for used feet that fit my machine. I have several of the ones I use a lot.
I have tried e:mailing Elna to see if they know of a 1/4" foot that will fit, to save wear and tear on the walking foot.
#15
When sewing clothing, the seams are subjected to a lot of pulling and tugging.....so the seam allowance needed to be wider and sometimes finished. But in a finished quilt, the seams don't get the pulling and are all secured by the actual quilting, so a smaller seam allowance works fine. If you already have a walking foot, then you can mark your machine bed (there are many ways) for 1/4" seam. The walking foot will be your best friend, specially for those long seams. I don't sew without it if I can.
#16
Super Member
Join Date: Jun 2010
Location: England Alton Towers
Posts: 6,673
Over this side of the pond some quilters have a geraric foot which it states fit any machine. The foot fits where the normal foot holder fits . Now the other arm in a geraric foot is a straight bar which goes above the screw for the needle. If I remember correctly berninas will not fit this foot. Try an amazon search will be back.
Looked on Amazon you have a selection although brother is popular. For 10$ try it.
Looked on Amazon you have a selection although brother is popular. For 10$ try it.
Last edited by DOTTYMO; 01-14-2013 at 08:36 AM. Reason: Went searching
#17
Member
Thread Starter
Join Date: Nov 2012
Location: Wales, UK
Posts: 58
Over this side of the pond some quilters have a geraric foot which it states fit any machine. The foot fits where the normal foot holder fits . Now the other arm in a geraric foot is a straight bar which goes above the screw for the needle. If I remember correctly berninas will not fit this foot. Try an amazon search will be back.
Looked on Amazon you have a selection although brother is popular. For 10$ try it.
Looked on Amazon you have a selection although brother is popular. For 10$ try it.
#18
Super Member
Join Date: Oct 2010
Location: northern California
Posts: 1,098
Okay, taking on board your advice, I thought I would treat myself to a 1/4" foot for my machine, especially as the walking foot was very expensive and I don't want to wear it out. Now the only problem seems to be that they don't make one for my machine , it's an Elna 2300.
#19
Member
Thread Starter
Join Date: Nov 2012
Location: Wales, UK
Posts: 58
There are a million quilters in this world who do not worry about exact 1/4" seams. It is important that you use the same measurement (same foot) for all your seams in a single quilt, especially if you are using a pattern. If your pattern has a zillion little pieces then a 1/4" foot could be very important. If you pieces are bigger it doesn't matter. So, your 5x7 foot quilt comes out 4'11"x6'10". Who cares? Many do, many don't. Many of us use a foot that is close and many of us don't even do that. Have you ever noticed that the deliberately "wonky" quits are often very exciting and beautiful? Everything doesn't have to be "exactly" anything. Just enjoy what you are doing and don't sweat the little stuff. Now, how do I post this anonomously so I don't get shot down by the would-be quilt police. Actually, I love you all, I just think a little relaxation wouldn't hurt.
#20
Super Member
Join Date: Jun 2010
Location: Chapel Hill
Posts: 1,086
You can easily set up a seam guide with a stack of tape that ends before the foot starts to set your quarter inch seam (or scant quarter inch - 1 to 2 threads smaller than 1/4 inch). Hopefully the picture attached correctly. I use that especially when using my walking foot as it is definitely wider than 1/4 inch.
One thing that I haven't seen mentioned regarding your original question about fraying of the seams - just don't be tempted to throw the top into the wash before you've layered and quilted it. Otherwise you will end up with a mess on the back.
Cheers, K
One thing that I haven't seen mentioned regarding your original question about fraying of the seams - just don't be tempted to throw the top into the wash before you've layered and quilted it. Otherwise you will end up with a mess on the back.
Cheers, K
Thread
Thread Starter
Forum
Replies
Last Post
Quilt4u
General Chit-Chat (non-quilting talk)
18
01-04-2011 06:40 PM
quiltorpainthorse
Introduce Yourself
23
01-04-2011 01:32 PM
Quilt4u
General Chit-Chat (non-quilting talk)
15
07-15-2010 03:06 PM