Go Back  Quiltingboard Forums >
  • Main
  • Thought I was Nuts! >
  • Thought I was Nuts!

  • Thought I was Nuts!

    Thread Tools
     
    Old 09-13-2012, 09:49 PM
      #1  
    Member
    Thread Starter
     
    Join Date: May 2012
    Location: Las Vegas
    Posts: 65
    Default Thought I was Nuts!

    I'm making a table topper, and the pattern says to cut one 8" square and bisect it twice for setting corners. Also cut two 5 5/8 squares and bisect once for 4 triangles. I thought I cut everything right, but the triangles were the same size, so I re-cut the 8" block, and they were still the same size!!
    After taking out my trusty calculator and figuring how big they should be, lo and behold THEY ARE THE SAME!!!
    Could have knocked me over with a feather. Why didnt' they just tell me to cut two 8"blocks and bisect twice, and I would have have the 8 triangles I needed.
    Okay, I'm finished, but thought you might like to know.

    Last edited by QuiltnNan; 09-14-2012 at 03:45 AM.
    SandyG is offline  
    Old 09-13-2012, 10:28 PM
      #2  
    Super Member
     
    woody's Avatar
     
    Join Date: Aug 2009
    Location: Canberra, Australia
    Posts: 2,135
    Default

    One is a half square triangle the other is a quarter square triangle, I hope this link explains it to you
    http://www.eliqg.com/documents/Triangles_Part1.pdf
    woody is offline  
    Old 09-13-2012, 10:33 PM
      #3  
    MTS
    Banned
     
    Join Date: Nov 2010
    Posts: 4,134
    Default

    It's all a matter of controlling where the bias edges end up and having the straight edges on the OUTSIDE of the quilt (or block).

    When you cut the setting triangles (aka QST - quarter square triangles), the two BIAS edges (two shorter sides) of each triangle will end up on the INSIDE of your quilt with the one STRAIGHT edge on the OUTSIDE.

    When you cut the corner triangles (aka HST - half square triangles), the one BIAS edge (longest side) of each triangle will be on the INSIDE of your quilt with the two STRAIGHT edges on the OUTSIDE.

    Even though the cut triangles might be the same size, each is intended for a different position in the quilt (or block).

    Now you know.
    It's a good thing.

    Last edited by MTS; 09-13-2012 at 10:40 PM.
    MTS is offline  
    Old 09-13-2012, 10:52 PM
      #4  
    Senior Member
     
    Toni C's Avatar
     
    Join Date: Mar 2009
    Location: Crosby,Texas
    Posts: 849
    Default

    Humm that makes sense.
    Toni C is offline  
    Old 09-14-2012, 05:01 PM
      #5  
    Super Member
     
    Join Date: Feb 2010
    Location: Maryland
    Posts: 3,586
    Default

    Originally Posted by MTS
    It's all a matter of controlling where the bias edges end up and having the straight edges on the OUTSIDE of the quilt (or block).

    When you cut the setting triangles (aka QST - quarter square triangles), the two BIAS edges (two shorter sides) of each triangle will end up on the INSIDE of your quilt with the one STRAIGHT edge on the OUTSIDE.

    When you cut the corner triangles (aka HST - half square triangles), the one BIAS edge (longest side) of each triangle will be on the INSIDE of your quilt with the two STRAIGHT edges on the OUTSIDE.

    Even though the cut triangles might be the same size, each is intended for a different position in the quilt (or block).

    Now you know.
    It's a good thing.
    Thank you for the explanation. It's good to know the "why" of things--now I know why and I won't forget "how"!
    virtualbernie is offline  
    Old 09-14-2012, 05:06 PM
      #6  
    Super Member
     
    Join Date: Aug 2011
    Location: metro Portland, OR
    Posts: 2,286
    Default

    Sometimes the instructions are not written as well as they should be, either.
    LadyElisabeth is offline  
    Old 09-15-2012, 12:43 AM
      #7  
    Super Member
     
    Join Date: Mar 2011
    Location: Mechanicsville, IA
    Posts: 1,497
    Default

    This is the bias edge thing is part of the reason for the Nifty Notions Half Square and Quarter Square rulers. They eliminate the need for cutting different size squares because you can cut both of those triangles from the same size strip.
    Silver Needle is offline  
    Old 09-15-2012, 09:19 AM
      #8  
    Power Poster
     
    Join Date: May 2008
    Location: MN
    Posts: 24,643
    Default

    Maybe the attached drawings might help illustrate the difference -

    Pretend the lines of the graph paper are the threads of the fabric -

    The sizes of the triangles are the same - but the grain lines on the longest edge change
    Attached Thumbnails triangles.jpg   triangles2.jpg  
    bearisgray is offline  
    Old 09-15-2012, 10:09 AM
      #9  
    Super Member
     
    MommaDorian's Avatar
     
    Join Date: Aug 2010
    Location: Sully, Iowa
    Posts: 2,390
    Default

    See, now I wouldn't have even thought there was a good reason. lol bearisgray, thanks for the visual help!!
    MommaDorian is offline  
    Related Topics
    Thread
    Thread Starter
    Forum
    Replies
    Last Post
    kwhite
    General Chit-Chat (non-quilting talk)
    122
    07-24-2021 01:36 PM
    sewnsewer2
    Main
    23
    07-03-2009 11:32 AM
    2 Doods
    Recipes
    4
    04-07-2008 06:32 PM
    sondray
    Recipes
    0
    03-27-2008 05:16 AM

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is On
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter