When machine quilting, what size stitch should I use?
#32
Originally Posted by Moon Holiday
The size stitch I use depends on the batting I use and which sewing machine I use. Regardless of what they say, there is a difference because of preset thread tension. I always do a sample of the type of stitch I want...and check both on front and back of the sample to see which one I like the look of best. It usually ends up between 2.5 and 3.
#33
Junior Member
Join Date: Jun 2009
Location: Kansas
Posts: 211
If you are talking when using the walking foot, it's a personal choice, what size looks good to you. Sometimes I use 2.0 up to a 3.0. Don't usually go any bigger than that. If you are talking free motion quilting, you are in total control of the stitch size because you dropped the feed dogs, and they are what pull the fabric through and make the stitch size what you have set on your machine. So with free motion and no feed dogs, it's up to your speed of moving the fabric and the speed of the machine. Believe me, it's easier to keep your stitches more regular and looking good if you will sew faster. Always have a practice sandwich made up and let yourself warm up before starting on that special project. I've found that some days I do a good job at quilting and some days it's just better to not do it and go do some other job. I've also read that if you practice about 15 minutes a day you will be suprised how much better the learning curve will be.
#34
I use 2 to sew the seams together, but a 4 for quilting. I try a sample piece first which always comes out exactly like what I want. But when I put the quilt in, my stitches come out smaller. Don't know if I'm using the wrong size needle. But samples come out just fine.
#35
Originally Posted by amandasgramma
2.0 to 2.6. BUT, I haven't taken the time to figure out how many stitches per inch that is. Eleanor Burns always says "15 stitches to the inch"....so.....what setting IS that?
#36
Originally Posted by Shelbie
I like the look of larger stitches, so I always use 4.5 or even 5. I find that this stitch is small enough to hold all layers securely and if you have to rip, it is not impossible to remove. I also find that the Janome walking foot tends to automatically use smaller stitches over thicker areas. Perhaps if I had the thread regulator option, this wouldn't be an issue. Experiment and see what works for you. No one is coming to measure your stitches and complain!
#37
I use a 2.5. A few months ago in class, I believe they said it's your preference, try a couple on a scrap square. I thought 2 was too small and I could go up to 3, but I didn't like it any more than 3. And yes different machines may be slightly different, so just try a few samples.
#38
So I have a question kinda related to this...I have always been confused about this...but when a pattern says stitch 12 stitches to the inch or 15 stitches to the inch ect., what is our machine set to example is 12 stitches to the inch set at 2.0...most common stitches to the inch is 12 or 15 so what number is set on the machine for these stitches?
#39
Senior Member
Join Date: Feb 2010
Location: Reno, Nevada
Posts: 794
I have learned a somewhat different technique (and consequently, I think, a much better look) for machine quilting:
First of all, use a TOPSTITCH NEEDLE. Schmetz labels "Topstitch" right on the cards holding packets of needles. They come in different sizes. I use a 12. The difference is that the topstitch needles have a larger hole which is made to accommodate a bit heavier thread --- it's that heavier thread which also makes the difference. They are also very sharp and penetrate the several layers quite nicely.
The THREAD is often sold as just that, "Topstitch", but technically, it (at least the Coats & Clark that I use) is labeled "HEAVY," but there is no gauge shown. It is similar to hand quilting weight thread but without the stiffness of the glace/wax. It is 100% polyester and as with most threads, comes in gorgeous colors. PLEASE NOTE: IT IS NOT THE "HEAVY" ONE THINKS OF FOR BUTTONHOLES, ETC. --- the buttonhole thread is so labeled. I usually use regular weight thread in the bobbin, but the heavy could be used as well (it just would wind less on the bobbin because of its thickness).
Next, when starting/stopping a line of quilting, I hold back on the fabric so that I get a double or triple stitch in one place which is a good lock without the forward/back overstitch look. The length of stitch I use is pretty close to 10-12 per inch and gives a nice look while still being very secure. (Run a line of stitching on a scrap and count stitches until you find your machine number which yields the correct number per inch. With a walking foot, the stitches should remain about the same, but adjust if needed.)
Summarily: A topstitch needle and heavy thread stitching out at 10-12 stitches per inch.
Hope this helps.
First of all, use a TOPSTITCH NEEDLE. Schmetz labels "Topstitch" right on the cards holding packets of needles. They come in different sizes. I use a 12. The difference is that the topstitch needles have a larger hole which is made to accommodate a bit heavier thread --- it's that heavier thread which also makes the difference. They are also very sharp and penetrate the several layers quite nicely.
The THREAD is often sold as just that, "Topstitch", but technically, it (at least the Coats & Clark that I use) is labeled "HEAVY," but there is no gauge shown. It is similar to hand quilting weight thread but without the stiffness of the glace/wax. It is 100% polyester and as with most threads, comes in gorgeous colors. PLEASE NOTE: IT IS NOT THE "HEAVY" ONE THINKS OF FOR BUTTONHOLES, ETC. --- the buttonhole thread is so labeled. I usually use regular weight thread in the bobbin, but the heavy could be used as well (it just would wind less on the bobbin because of its thickness).
Next, when starting/stopping a line of quilting, I hold back on the fabric so that I get a double or triple stitch in one place which is a good lock without the forward/back overstitch look. The length of stitch I use is pretty close to 10-12 per inch and gives a nice look while still being very secure. (Run a line of stitching on a scrap and count stitches until you find your machine number which yields the correct number per inch. With a walking foot, the stitches should remain about the same, but adjust if needed.)
Summarily: A topstitch needle and heavy thread stitching out at 10-12 stitches per inch.
Hope this helps.
Thread
Thread Starter
Forum
Replies
Last Post
sewingsuz
Main
7
01-28-2013 08:29 PM
AngelinaMaria
Main
3
01-08-2012 06:56 PM