Question about interfacing for t-shirt quilts
03-09-2013, 06:36 PM
#1
Super Member
Thread Starter
Join Date: May 2009
Location: Back home in Louisiana for now....where next?? who knows....
Posts: 3,180
Question about interfacing for t-shirt quilts
I am going to make a t-shirt quilt and I read where they say to use non-woven but what I have is woven......I think that is how it goes.......whichever it is I have the opposite. Will it really make that much of a difference?
03-09-2013, 08:48 PM
#3
Super Member
Join Date: May 2010
Posts: 1,658
I like the tricot (knit) fusible. It gives it a nice weight with out being heavy. BUT ...once you quilt it, the ONLY person who will know what fusible you used is...YOU! No Quilt Police are going to come and take your quilt apart, only to give you a citation of fusible non-compliance. :-D Try a piece of a knit and what ever you have and see which one you like better.
03-10-2013, 08:50 AM
#4
Senior Member
Join Date: Apr 2010
Location: Sunny Arizona
Posts: 476
I also use the knit fusible interfacing and it keeps the shirt soft and flexible and doesn't seem to add much weight to the shirt. I always make sure that the "stretch" in the interfacing goes in the opposite direction from the shirt. That shirt will not give in any direction while you are working with it. Ann
03-10-2013, 09:15 AM
#5
Super Member
Join Date: Jul 2010
Location: Central Minnesota
Posts: 1,131
It was suggested to use the ''cheapest" fusible interfacing available, by a longarmer. We went to Joann's found the cheap Pellon on a small bolt. It was fusible, very easy to use. It worked very well.
03-10-2013, 01:50 PM
#6
Senior Member
Join Date: Sep 2010
Location: NM
Posts: 989
The stretch of the t shirt is around your body, figure out the stretch of the woven interfacing, usually selvage to selvage. One goes up and down and the other side to side. Make a big cross with the two pieces of fabric.
03-10-2013, 01:58 PM
#7
Power Poster
Join Date: Feb 2009
Location: Northern Michigan
Posts: 12,861
woven interfacing is fine to use...the difference in woven & non-woven is the fiber- woven is more like a fabric- non-woven is more like a soft paper- non-woven tears easily- woven does not-
you can use which ever one you have & want to use. (do check your iron setting- the woven *might* shrink a little with too much heat- you could use a press cloth to protect it) i tend to always use woven fusable interfacing- i just like to work with it better than the non-wovens. tricot is nice too- but if you already have the woven there is no reason to go buy something different
you can use which ever one you have & want to use. (do check your iron setting- the woven *might* shrink a little with too much heat- you could use a press cloth to protect it) i tend to always use woven fusable interfacing- i just like to work with it better than the non-wovens. tricot is nice too- but if you already have the woven there is no reason to go buy something different
03-11-2013, 02:45 PM
#8
Junior Member
Join Date: Nov 2011
Location: Tomball (near Houston), Texas
Posts: 172
I just finished two t-shirt quilts and I used the cheap stuff from Joann's too. The label says "Pellon, Sheerweight Fusible #906F, 100% Polyester". It only cost $2.49 per yd. and you will need lots of it, because you have so much waste. I went back 2 times for more. This one was thin and soft enough that you still had the t-shirt softness, but it had no more stretch. I recommend it.
Thread
Thread Starter
Forum
Replies
Last Post
