BIG boo boo
#12
Super Member
Join Date: Sep 2010
Location: Corpus Christi, Texas (that's me!)
Posts: 3,771
Originally Posted by eparys
To heck with the lint roller - get some wide packing tape - make a large loop sticky side out around your hand and "pat" away. It is MUCH stickier than a lint roller (now you wonder why I know this . . . LOL) and works so much quicker and easier (at least for me).
Before you "rip out" next time - I have found if you have loops on the back, if you clip the back thread once where it goes around the curves - the piece of backing thread pulls out easily. Then the top thread is not held down and it too pulls out in a long strand.
Sorry - Good Luck!
Before you "rip out" next time - I have found if you have loops on the back, if you clip the back thread once where it goes around the curves - the piece of backing thread pulls out easily. Then the top thread is not held down and it too pulls out in a long strand.
Sorry - Good Luck!
It will come in handy sometime.
#13
Static build up in the bobbin will cause lots of loops and birdnesting. I started using the Bobbin Genies and they work! Sharon Schamber at a class said they were a must for her machine quilting. When I have to pick out quilting stitches and have all those little threads to remove I just take a deep breath and relax and get it done.
#14
Same thing happened to me and I took the backing off and turned it around as I had tons of backing fabric that wouldn't be used. This saved me more time that a lint roller cause if your lint roller isn't sticky enough you still have to pull the threads out.
#15
Originally Posted by eparys
Before you "rip out" next time - I have found if you have loops on the back, if you clip the back thread once where it goes around the curves - the piece of backing thread pulls out easily. Then the top thread is not held down and it too pulls out in a long strand.
:thumbup:
#16
Super Member
Thread Starter
Join Date: Aug 2009
Location: long island ny
Posts: 1,337
Originally Posted by BellaBoo
Static build up in the bobbin will cause lots of loops and birdnesting. I started using the Bobbin Genies and they work! Sharon Schamber at a class said they were a must for her machine quilting. When I have to pick out quilting stitches and have all those little threads to remove I just take a deep breath and relax and get it done.
#17
Power Poster
Join Date: Feb 2009
Location: Northern Michigan
Posts: 12,861
don't throw your unbound-unquilted top into the wash! you will really create a mess- you can use a lint roller- or masking tape to help remove the little threads.
wait until it is quilted and bound- then wash it.
wait until it is quilted and bound- then wash it.
#19
Super Member
Thread Starter
Join Date: Aug 2009
Location: long island ny
Posts: 1,337
I thought of that...duct tape is the stickiest. If I had laundered it I would have serged the edges first. But, I'm going the tape route. I will launder it after quilting and binding as there are lots of needles holes to be closed up.
#20
I was having the intermitten eyelash problem on the back and couldn't figure out why. I started doing research and found out that when you thread your machine, you need to be sure the presser foot is UP so the thread can get properly seated between the discs. I have made sure ever since and have not had the problem again.
Also, when removing the bad quilting, I also, as stated above, snipped and pulled out the bottom thread which left the top thread easy to remove...and there were yards and yards of it.
Also, when removing the bad quilting, I also, as stated above, snipped and pulled out the bottom thread which left the top thread easy to remove...and there were yards and yards of it.
Thread
Thread Starter
Forum
Replies
Last Post
sweet
General Chit-Chat (non-quilting talk)
28
02-21-2012 12:58 PM