Go Back  Quiltingboard Forums >
  • Main
  • For Vintage & Antique Machine Enthusiasts
  • Hopefully bringing a Singer 401g back from a long sleep >
  • Hopefully bringing a Singer 401g back from a long sleep

  • Hopefully bringing a Singer 401g back from a long sleep

    Thread Tools
     
    Old 09-14-2020, 04:35 AM
      #31  
    Super Member
     
    Join Date: Sep 2015
    Posts: 1,963
    Default

    Polishes vary a lot, I have had metal polishes starting to dissolve paints (like on Elnas), you can't go by random choice, you have to get the right stuff for the job. I lean towards furniture polishes suitable for shellac, or resin type car polishes. On very special machines I would hardly dare anything but gentle cleaning. I allow a few signs of wear and age, I don't mind. I do touch ups of chips and if there are spots where the paint is missing or very worn. A machine should be in bad shape before I do a refinish and complete stripping of the old paint. I tend to avoid too much rust or damaged chrome. I clean off all grime and dirt, usually with a bit of effort, and it takes a few turns of cleaning and polishing before I get there. Maybe a bit of dissasembly here and there too. I poke around with tooth picks, cotton swabs,...

    It looks like your machine is cleaning up very well. Any test stiching, or new leather belt?

    Last edited by Mickey2; 09-14-2020 at 04:38 AM.
    Mickey2 is offline  
    Old 09-14-2020, 09:20 AM
      #32  
    Super Member
     
    Rebaquilts's Avatar
     
    Join Date: May 2020
    Location: Sunset Coast of Michigan
    Posts: 1,037
    Default Wd40

    I would avoid using wd40 as it has chemicals that are unnecessary and left overs will continue to break down oil. Instead, use kerosene, that was recommended at the time and several SM mechanic experts recommend it. I use a kerosene alternative, called klean heat, it doesn't have the smell. Just my opinion. Good luck!! Reba
    Rebaquilts is offline  
    Old 09-14-2020, 12:12 PM
      #33  
    Member
    Thread Starter
     
    Join Date: Sep 2020
    Posts: 15
    Default

    Originally Posted by Mickey2
    It looks like your machine is cleaning up very well. Any test stiching, or new leather belt?
    No test stitching yet, altough I can't wait. I still need to clean the treadle. Today I cleaned the machines covers.
    I'll be needing a new belt definitely. The original one snapped close to were both ends join so with any luck I'll be able to cut the broken part and make a new joint.
    Then it's a matter of learning how to thread the line and work the machine.

    Originally Posted by Rebaquilts
    I would avoid using wd40 as it has chemicals that are unnecessary and left overs will continue to break down oil. Instead, use kerosene, that was recommended at the time and several SM mechanic experts recommend it. I use a kerosene alternative, called klean heat, it doesn't have the smell. Just my opinion. Good luck!! Reba
    Thank you Reba. I was fortunately able to get rid of all the old oil using only sewing machine oil.
    Jay401 is offline  
    Old 09-14-2020, 12:17 PM
      #34  
    Super Member
     
    leonf's Avatar
     
    Join Date: May 2016
    Location: near Topeka kansas
    Posts: 4,524
    Default

    Jay, learning to treadle is a skill in itself. practice long enough before you thread it that you can carry on a conversation while keeping the machine spinning the correct way. if you reverse directions when threaded you will snap the thread.
    leonf is offline  
    Old 09-14-2020, 12:28 PM
      #35  
    Member
    Thread Starter
     
    Join Date: Sep 2020
    Posts: 15
    Default

    Thank you. I've been watching videos and it seems like a lot of skill and practice goes into it. I just couldn't understand if the thread breaks if you too fast, don't keep a good rythm or because if you just let go of the treadle the needle moves back and snaps the thread. The problem with watching talented people is that they make everything look easier than it is.

    Originally Posted by leonf
    Jay, learning to treadle is a skill in itself. practice long enough before you thread it that you can carry on a conversation while keeping the machine spinning the correct way. if you reverse directions when threaded you will snap the thread.
    Jay401 is offline  
    Old 09-14-2020, 12:43 PM
      #36  
    Super Member
     
    Join Date: Sep 2015
    Posts: 1,963
    Default

    I have only done a little bit of treadling, but I dare say it is within doable. You can go full speed, with zigzag patterns you do that some times. the tricky thing is the large wheel on the treadle can end up turing the wrong way. That is part of the learning process, just make sure you start by guiding the wheel the correct way on the first stitches and after everytime you stop and start again. A steady pace is preferable, it is not too difficult and don't worry. The machine does most of the job regarding stiching and fabric feed, thread snapping should not be a problem and you only need the really fine tuned skills for freemotion like quilting and embroidery.

    Last edited by Mickey2; 09-14-2020 at 12:46 PM.
    Mickey2 is offline  
    Old 09-14-2020, 05:20 PM
      #37  
    Senior Member
     
    Join Date: Jan 2015
    Location: Wisconsin
    Posts: 474
    Default

    Quite a change in a short amount of time. Good for you!
    0xygen tubing, aquarium tubing, window screen spline, can also be used as a treadle belt alternative. A leather treadle belt can usually be found online for under $10.00.
    WIChix is offline  
    Old 09-16-2020, 04:28 AM
      #38  
    Junior Member
     
    Join Date: Jan 2020
    Location: Ontario
    Posts: 299
    Default

    Looking forward to seeing the treadle 401 finished
    Hooligan is offline  
    Old 09-16-2020, 06:50 AM
      #39  
    Member
    Thread Starter
     
    Join Date: Sep 2020
    Posts: 15
    Default

    Thank you Mickey and WIChix. I'll order some treadle belt from Amazon and some needles while I'm at it.

    Originally Posted by Hooligan
    Looking forward to seeing the treadle 401 finished
    Thank you. For now it's on Amazons court, but as soon as I'm finished I'll post about.

    Meanwhile here's a before and after of the wood top and a shot of the assembled machine+treadle.





    Jay401 is offline  
    Old 09-16-2020, 06:59 AM
      #40  
    Super Member
     
    OurWorkbench's Avatar
     
    Join Date: Mar 2015
    Location: Denver, CO
    Posts: 4,350
    Default

    Originally Posted by Jay401
    ...Meanwhile here's a before and after of the wood top and a shot of the assembled machine+treadle. ...
    Beautiful, very well done. What did you use on the wood?

    Janey - Neat people never make the exciting discoveries I do.
    OurWorkbench is offline  

    Posting Rules
    You may not post new threads
    You may not post replies
    You may not post attachments
    You may not edit your posts

    BB code is On
    Smilies are On
    [IMG] code is On
    HTML code is Off
    Trackbacks are Off
    Pingbacks are Off
    Refbacks are Off



    FREE Quilting Newsletter