Wizard ZZ machine update
#1
Super Member
Thread Starter
Join Date: Feb 2012
Posts: 8,091
Wizard ZZ machine update
Two years ago Miriam give me a rusted frozen up Wizard ZZ machine for parts.
You can see the rust under the face plate.
I worked on it now and again and it would not cooperate. The needle bar and presser foot bar were rusted tight. I soaked it in kerosene, sewing machine oil, penetrating oil, Tri-Flow and it would not budge.
Finally I took everything off of it that could be removed without damaging anything and broke out the propane torch.
There is no plastic in the nose of the machine, so I heated the bars up till they smoked then doused them in ATF. I can't remember how many times I did this, but finally that worked. I got them freed up.
I oiled the entire machine with ATF to make sure it was free. ( Note I don't recommend ATF, but at the time I was considering parting this machine out so I figured it couldn't hurt.)
About a year ago I put the machine and all it's parts in a cardboard box on my work bench in the garage. Today out of curiosity I went out there and gave it a turn. It's still free as can be. I worked all the controls, they are still free too.
So, now I have the urge to bring it inside and really do a thorough cleaning and adjusting and see if it sews. If so, since it has no motor or case, I'm thinking of trying it in a treadle. It's got lots of built in patterns, so if it worked it would be a neat all purpose treadle machine.
Joe
You can see the rust under the face plate.
I worked on it now and again and it would not cooperate. The needle bar and presser foot bar were rusted tight. I soaked it in kerosene, sewing machine oil, penetrating oil, Tri-Flow and it would not budge.
Finally I took everything off of it that could be removed without damaging anything and broke out the propane torch.
There is no plastic in the nose of the machine, so I heated the bars up till they smoked then doused them in ATF. I can't remember how many times I did this, but finally that worked. I got them freed up.
I oiled the entire machine with ATF to make sure it was free. ( Note I don't recommend ATF, but at the time I was considering parting this machine out so I figured it couldn't hurt.)
About a year ago I put the machine and all it's parts in a cardboard box on my work bench in the garage. Today out of curiosity I went out there and gave it a turn. It's still free as can be. I worked all the controls, they are still free too.
So, now I have the urge to bring it inside and really do a thorough cleaning and adjusting and see if it sews. If so, since it has no motor or case, I'm thinking of trying it in a treadle. It's got lots of built in patterns, so if it worked it would be a neat all purpose treadle machine.
Joe
#4
Power Poster
Join Date: Mar 2011
Location: Somewhere
Posts: 15,506
It seemed like a great machine at the time I was overwhelmed with the other 60 or so... I betcha it would treadle - and you can adjust the needle setting!!! I think it was one of the top 10 worst machines.
#5
Banned
Join Date: Aug 2014
Location: Victorian Sweatshop Forum
Posts: 4,096
I'd love to have one like that one. My Selectomatic has the needle position lever right about in the same place. I've discovered I don't like it right there. I've been quilting a larger quilt on it and every time I notice my straight stitches aren't straight but sort of going in a tiny random zig zag, I've managed to knock that lever out of it's detent so the needle bar was free to do whatever it wanted to. Had a few sessions with the seam ripper and did the binding on my 201 instead.
Cari
Cari
Thread
Thread Starter
Forum
Replies
Last Post
Likethedog
For Vintage & Antique Machine Enthusiasts
25
08-17-2020 06:11 AM
toriabelle
For Vintage & Antique Machine Enthusiasts
2
06-01-2013 06:38 PM
Ann63
For Vintage & Antique Machine Enthusiasts
11
01-09-2011 09:00 PM