Go Back  Quiltingboard Forums > Main
Making Your Own Ironing Board--Did you use canvas or silver ironing fabric? >

Making Your Own Ironing Board--Did you use canvas or silver ironing fabric?

Making Your Own Ironing Board--Did you use canvas or silver ironing fabric?

Old 07-15-2013, 06:57 AM
  #1  
Senior Member
Thread Starter
 
Join Date: Aug 2011
Location: The California Hills
Posts: 626
Default Making Your Own Ironing Board--Did you use canvas or silver ironing fabric?

I am getting ready to make my own custom ironing board that will fit on my kitchen island (3 feet by 4 feet). I purchased a few yards of silver ironing board fabric from Joann's but have seen on a number of blogs and "how to" videos that most people are using canvas.

Is there a reason to use one or the other? I thought the silver fabric stays cooler so you don't burn your hands as much when picking up the pressed blocks, etc.? The silver fabric I got is pretty thin though so I'm not sure if I should look for a higher quality one somewhere else. I'm thinking I'll make a small iron pad first to see how it works.

If you made your own iron board/pad, did you use one, two or more thicknesses of batting? Sharon Shamber used only one thin layer of batting for hers--she says it is best to have a hard surface. However, I saw lots of other blogs/video use 3 to even 5 layers of batting.

If I decide to use canvas, is there a particular kind I should search for (or quality type)?? Thanks.
AngelinaMaria is offline  
Old 07-15-2013, 07:32 AM
  #2  
Super Member
 
Scissor Queen's Avatar
 
Join Date: Jul 2009
Location: Southwest Kansas
Posts: 4,820
Default

I have taken a couple of classes from nationally known teachers and they all say to take that silver stuff off your ironing board because it's slippery. I have cotton duck on my board and it grips nicely so I don't get distortion when I press. It has one layer of a felted type cotton padding that's not much thicker than one layer of cotton batting.
Scissor Queen is offline  
Old 07-15-2013, 07:38 AM
  #3  
Super Member
 
Join Date: Aug 2011
Location: Albany, Georgia
Posts: 1,715
Default

I covered mine with the silver stuff but I cover that with an old sheet so I can take it off and wash it when it gets stiff from all the starch I use, been working good for about 5 years now. I tie a piece of elastic around the sheet on the table to hold it in place.
quilts4charity is offline  
Old 07-15-2013, 07:45 AM
  #4  
Super Member
 
thimblebug6000's Avatar
 
Join Date: Jun 2007
Location: British Columbia
Posts: 8,023
Default

I put one layer of warm & natural and then one layer of the insulbrite and then topped it with a heavy cotton twill for my "big board" and it works great. Mine is all stapled onto a sheet of plywood & sits over my regular ironing board. IF the top gets too discoloured, I will just add another layer of the cotton twill. I don't like a really soft surface to iron on and this is perfect for me. Good luck with yours!
thimblebug6000 is offline  
Old 07-15-2013, 08:18 AM
  #5  
Power Poster
 
Join Date: Dec 2008
Location: Western Wisconsin
Posts: 12,930
Default

I used a layer of Warm n Natural and covered that with duck cloth (unwashed). Mine is stapled on; I would not use duck cloth if you are making a cover that will be taken off and washed.

I think Sharon Schamber is correct and a hard surface works better for quilting. You can get the seams flatter. Cushioning is more important for embroidery.
Prism99 is offline  
Old 07-15-2013, 08:26 AM
  #6  
Super Member
 
Join Date: Aug 2010
Location: Piedmont Virginia in the Foothills of the Blue Ridge Mtns.
Posts: 8,562
Default

Thin plywood 38" x 28".
Covered with plastic garbage bag - one layer.
One layer Warm and Natural batting.
One layer silver ironing board fabric.
Jan in VA is offline  
Old 07-15-2013, 08:28 AM
  #7  
Power Poster
 
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,431
Default

I have one layer of cotton batt over plywood. I covered it with good quality muslin but I need to replace it. I have ironed so much on the surface that the fabric is brown and cracking off. I have used freezer paper ironed to my surface to extend the use and that works well. If you already have the silver stuff, I would use it. You can always replace it later if you don't like it.
Tartan is offline  
Old 07-15-2013, 08:28 AM
  #8  
Senior Member
 
omaluvs2quilt's Avatar
 
Join Date: Nov 2011
Location: Las Vegas, NV
Posts: 926
Default

My mom used the silver stuff and its now lifting off onto her fabric when she starches. I used the canvas with 1 layer of 100% cotton batting and it works great! It does grip your blocks to help cut down on distortion while pressing.
omaluvs2quilt is offline  
Old 07-15-2013, 08:58 AM
  #9  
Senior Member
 
Join Date: Nov 2012
Posts: 903
Default

I used 2 layers of warm and natural - and made a pillowcase out of cotton duck that fits snugly, but can be taken off and washed if I want - I just did it with a 2x2 piece of underlayment - not too big, but big enough .
maminstl is offline  
Old 07-15-2013, 12:05 PM
  #10  
Super Member
 
leatheflea's Avatar
 
Join Date: Jul 2010
Location: martinsville Indiana
Posts: 4,461
Default

plywood, cotton batting, and canvas on mine.
leatheflea is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
carolaug
Links and Resources
15
05-17-2013 12:25 PM
craftybear
Links and Resources
15
04-07-2013 02:59 AM
craftybear
Links and Resources
7
06-02-2011 04:39 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


FREE Quilting Newsletter