Vintage Sewing Machine Shop.....Come on in and sit a spell
Super Member
Join Date: Dec 2010
Location: Michigan
Posts: 3,334
I just got home from Lowe's...... denatured alcohol, naptha, Linseed oil and spray shellac in hand. So I'm ready to try the clean-up on the old machine.
Glenn, can you tell me how to tell if the current finish is shellac or something else? and...... can you tell me details about adding shellac if the finish is gone. I just need to know before I do something awful. Thanks.
Glenn, can you tell me how to tell if the current finish is shellac or something else? and...... can you tell me details about adding shellac if the finish is gone. I just need to know before I do something awful. Thanks.
Super Member
Join Date: Mar 2010
Location: Huntsville, AL
Posts: 2,609
Put alcohol on rag and touch to the finish in place where it will not be seen usually on the rear arm where the motor boss would be. If the finish gets tacky or soft then it is shellac. If nothing happens then it is a varnish of somekind and this tech will not work. You can spray on the clear shellac or you can use finger and rag. Did finger in a little shellac with a couple of drops of linseed oil and lightly rub on the finish in a circular motion then lift your finger and go over lightly in one direction.
Most machines 60 years + will normally be shellac. This shellac clear coat was applied to protect the decals and make the japan black shine a little. Hope this helpr you. Skip
Most machines 60 years + will normally be shellac. This shellac clear coat was applied to protect the decals and make the japan black shine a little. Hope this helpr you. Skip
Super Member
Join Date: Dec 2010
Location: Michigan
Posts: 3,334
Thanks so much. The machine I'm wanting to try this on is an 1899 Singer Model 27. At least that's what Charlee said she thought it would be. I still have a stuck stitch regulator but everything else is working well. And I'll keep working on her till she's feeling healthy again..... she's getting better every day. Since I learned on a treadle machine so many years ago she'll be a fun memory back. Thanks again, Jean (nanna-up-north)
Super Member
Join Date: Mar 2010
Location: Huntsville, AL
Posts: 2,609
Jean your clear coat on this machine is shellac. You are ready to start working and having fun. Skip
Super Member
Join Date: Dec 2011
Location: Northern CA near Sacramento
Posts: 1,107
I was playing/ sorting some sewing machine needles this afternoon.
The differences are amazing. I shot a picture of a few of them.I
thought some of you might like to see the picture.
[ATTACH=CONFIG]324808[/ATTACH]
The differences are amazing. I shot a picture of a few of them.I
thought some of you might like to see the picture.
[ATTACH=CONFIG]324808[/ATTACH]
Super Member
Join Date: Mar 2010
Location: Huntsville, AL
Posts: 2,609
[QUOTE=Mizkaki;5111400]I was playing/ sorting some sewing machine needles this afternoon.
The differences are amazing. I shot a picture of a few of them.I
thought some of you might like to see the picture.
Thank you for the needle info, I did not know the the 190R could sub as a Davis long. Skip
The differences are amazing. I shot a picture of a few of them.I
thought some of you might like to see the picture.
Thank you for the needle info, I did not know the the 190R could sub as a Davis long. Skip
Super Member
Join Date: Dec 2011
Location: Northern CA near Sacramento
Posts: 1,107
Glenn,
The Davis long is a flat shank needle while the MTx190 is round. This does not seem to make much difference in the smaller sizes. With the larger sizes the needle is pushed closer to the other side of the needle hole and could rub it. The round shank will push the scarf slightly further from the hook so there is a slight chance of skipping stitches. The people over at Yahoo's WeFixIt group and Treadleon have found this needle to be an OK substitute. Joe has tried this MTx190 in a size 12 and says it works well.
Cathy
[QUOTE=Glenn;5111419]
The Davis long is a flat shank needle while the MTx190 is round. This does not seem to make much difference in the smaller sizes. With the larger sizes the needle is pushed closer to the other side of the needle hole and could rub it. The round shank will push the scarf slightly further from the hook so there is a slight chance of skipping stitches. The people over at Yahoo's WeFixIt group and Treadleon have found this needle to be an OK substitute. Joe has tried this MTx190 in a size 12 and says it works well.
Cathy
[QUOTE=Glenn;5111419]
I was playing/ sorting some sewing machine needles this afternoon.
The differences are amazing. I shot a picture of a few of them.I
thought some of you might like to see the picture.
Thank you for the needle info, I did not know the the 190R could sub as a Davis long. Skip
The differences are amazing. I shot a picture of a few of them.I
thought some of you might like to see the picture.
Thank you for the needle info, I did not know the the 190R could sub as a Davis long. Skip
Super Member
Join Date: Mar 2010
Location: Huntsville, AL
Posts: 2,609
Glad to konw this Cathy, I have always used a 15X1 and cheated it down with very good results. I made a guide and marked them so I know how far to lower them in the clamp. Although I have a stash of Davis longs I am stingy with them lol Skip
Thread
Thread Starter
Forum
Replies
Last Post
Stitchnripper
Main
5
10-17-2018 09:01 AM
AngieS
Main
38
10-06-2011 10:06 PM
craftybear
Offline Events, Announcements, Discussions
34
09-09-2011 12:36 PM