Half Square Triangle Ruler
#21
If I am making a lot, I'll do the square sewn down the middle. I've not had luck with the method of using a bigger square and sewing so you end up with a bunch of identical HSTs. I am fine with trimming, so I will start out with slightly bigger squares so what I end up with is always exact.
When I want more randomness, then I'll use my easy angle just like sewbizgirl does.
When I want more randomness, then I'll use my easy angle just like sewbizgirl does.
#23
Power Poster
Join Date: Jan 2011
Location: Southern USA
Posts: 16,412
Here is my problem with the Block Loc.
I used the 6 1/2 Block Loc to square up two HSTs. One on the left is perfect, right one is no use at all. There is no marking on the ruler which groove side to use on the seam and both sides fit. So what am I doing wrong?
[ATTACH=CONFIG]573307[/ATTACH] [ATTACH=CONFIG]573308[/ATTACH]
I used the 6 1/2 Block Loc to square up two HSTs. One on the left is perfect, right one is no use at all. There is no marking on the ruler which groove side to use on the seam and both sides fit. So what am I doing wrong?
[ATTACH=CONFIG]573307[/ATTACH] [ATTACH=CONFIG]573308[/ATTACH]
Last edited by Onebyone; 05-18-2017 at 08:16 AM.
#24
Junior Member
Join Date: Feb 2017
Location: St. Louis area
Posts: 212
I have a love-hate relationship with HST's. I fell in love with a pattern and just had to make it. It turned out to be all HST's and squares measuring 2 inches finished. Needless to say, by the time I finished that top I was BURNED OUT on HST's. And I still am! For Christmas I made another quilt that needed HST's (for granddaughter) and I knew I had to find a way to make HST's easier than one or two at a time(remember, I'm still burned out). So I went searching. If I have to make more than 4 HST's,( and if you make quilts, who doesn't) I use the method that makes 8 at a time. I found a chart that tells you what size to cut the fabric for whatever size HST you need. And they don't need trimming!!!! Even my scrappies(is that right?) will now get HST's using this method. For me the wheel is now fixed.
JAN
JAN
#25
Power Poster
Join Date: Jan 2011
Location: Southern USA
Posts: 16,412
I have the 8 in one. Fancy but is all in one so it makes it a little easier. http://www.ciscosewingsuppliesandnot...ngle-tool.html The chart size was online. I downloaded it and it's on the ruler. I have the WonderCut ruler and it's accurate. But time consuming.
#26
#27
Senior Member
Join Date: Oct 2012
Posts: 817
I tried the Quilt in a Day ruler where you can trim up before you open your HST but it kept slipping and caused me pain so I'm going to invest in a Bloc Loc ruler, they're expensive so I'm going
to order the biggest one, it's 12". I've tried my regular ruler but it was very hard to get to stay as well.
to order the biggest one, it's 12". I've tried my regular ruler but it was very hard to get to stay as well.
hugs,
Charlotte
#28
Here is my problem with the Block Loc.
I used the 6 1/2 Block Loc to square up two HSTs. One on the left is perfect, right one is no use at all. There is no marking on the ruler which groove side to use on the seam and both sides fit. So what am I doing wrong?
[ATTACH=CONFIG]573307[/ATTACH] [ATTACH=CONFIG]573308[/ATTACH]
I used the 6 1/2 Block Loc to square up two HSTs. One on the left is perfect, right one is no use at all. There is no marking on the ruler which groove side to use on the seam and both sides fit. So what am I doing wrong?
[ATTACH=CONFIG]573307[/ATTACH] [ATTACH=CONFIG]573308[/ATTACH]
Check their video on how to use the bloc loc. Works fine for me.
Still have to be careful how I trim. I find the way I stand is
important. I prefer to add a piece of clear Nexcare tape under
the small ruler to prevent it from slipping too much but otherwise
it works fine.
https://www.youtube.com/watch?v=5JttQmP4cT4
#29
Just remember to put the logo "Bloc-Loc" on the low side of your
HST, i.e. the side where there's no seam. Here's another video.
Very simple.
https://www.youtube.com/watch?v=gUqbjcV36IE
HST, i.e. the side where there's no seam. Here's another video.
Very simple.
https://www.youtube.com/watch?v=gUqbjcV36IE
Thread
Thread Starter
Forum
Replies
Last Post
lindamar
Main
18
09-20-2011 06:50 AM
craftybear
Links and Resources
2
08-08-2011 08:45 AM
craftybear
Links and Resources
4
04-05-2011 03:05 PM