Help...I'm a 1/4" Short!
05-26-2011, 03:21 AM
#12
Banned
Join Date: Mar 2010
Location: Sturbridge, Ma
Posts: 3,992
The design is basicaly a 9 patch. So, if all your blocks are the same size it won't matter if they are alightly off if all the same size.
Did you measure after your first half square triangle block. Your accuracy or inaccuracy begins the first time you sew two pieces together. If the section is not the correct size then correction in seam allowance should be adjusted then.
Did you measure after your first half square triangle block. Your accuracy or inaccuracy begins the first time you sew two pieces together. If the section is not the correct size then correction in seam allowance should be adjusted then.
05-26-2011, 04:00 AM
#13
Power Poster
Join Date: Mar 2011
Location: western NY formerly MN, FL, NC, SC
Posts: 51,430
Originally Posted by Twisted Quilter
I doing the Perpetual Motion block from DelawareQuilts.com. I'm even marking the 1/4" seam and it still doesn't help. I'll have to check the ruler I'm using.
05-26-2011, 04:53 AM
#14
Power Poster
Join Date: May 2009
Location: NY
Posts: 10,590
Block it! I have often been able to eke out the 1/4 by blocking. To block your coming up short block this is how I do it. I have a cork bulletin board that I drew my 12 1/2" square on with a permanent sharpy marker using my square 12 1/2" ruler. I pin my block to it first doing opposite corners then the sides matching up the edges of my block to my marked outline on the bulletin board. You need to stretch it a bit but usually this is not a problem and I use a lot of pins to do this. Then take a spray bottle with water and spritz the pinned block until it is thoroughly saturated. Walk away and let it air dry overnight. When you unpin it it will retain the squared size of 12 1/2".
05-26-2011, 05:33 AM
#15
Power Poster
Join Date: Jun 2007
Location: middle of a farmer field
Posts: 14,840
Those pesky hst. They get a fair number of people.
Check the size of them before putting the rest of the block together. They should be 4 1/2" each. If not it is a matter of seeing where it is that you are loosing out.
Cutting. Even is you slant the cutter in towards the ruler a bit you can end up with a slightly smaller piece. It adds up even though it doesn't look much different.
Sewing. Double check your seam. Especially with so many even one or two threads yet again add up
Pressing. Yes you can even loose some in the way you press. If everything else is good when you double checked. Try different ways. Yes even pressing open.
Check the size of them before putting the rest of the block together. They should be 4 1/2" each. If not it is a matter of seeing where it is that you are loosing out.
Cutting. Even is you slant the cutter in towards the ruler a bit you can end up with a slightly smaller piece. It adds up even though it doesn't look much different.
Sewing. Double check your seam. Especially with so many even one or two threads yet again add up
Pressing. Yes you can even loose some in the way you press. If everything else is good when you double checked. Try different ways. Yes even pressing open.
05-26-2011, 05:34 AM
#16
Power Poster
Join Date: Mar 2011
Location: Ontario, Canada
Posts: 41,610
Bummer! I just finished one that had to be 12½ also. I did a trial block out of scraps and it came out about ¼ under. I did a scant ¼ on the real block and it is slightly over. I figured better over than under but some of my points may disappear. If it is for myself it wouldn't bug me so much because if all your blocks are repeated for the top, size is not as important as consistency. Good luck!
05-26-2011, 05:39 AM
#17
Senior Member
Join Date: Apr 2011
Location: Australia
Posts: 661
Originally Posted by feline fanatic
Block it! I have often been able to eke out the 1/4 by blocking. To block your coming up short block this is how I do it. I have a cork bulletin board that I drew my 12 1/2" square on with a permanent sharpy marker using my square 12 1/2" ruler. I pin my block to it first doing opposite corners then the sides matching up the edges of my block to my marked outline on the bulletin board. You need to stretch it a bit but usually this is not a problem and I use a lot of pins to do this. Then take a spray bottle with water and spritz the pinned block until it is thoroughly saturated. Walk away and let it air dry overnight. When you unpin it it will retain the squared size of 12 1/2".
05-26-2011, 05:48 AM
#18
Senior Member
Join Date: Nov 2010
Location: Northern Idaho
Posts: 476
Instead of measuring your seam.....try this. Cut 3 pieces, each 1 1/2" by 4". Sew the long sides together using what you think is a 1/4" seam. Press and measure. Your piece should measure 3 1/2 inches by 4 inches.
If it is less than 3 1/2" you need to take a narrower seam. Hope this helps you.
If it is less than 3 1/2" you need to take a narrower seam. Hope this helps you.
05-26-2011, 05:58 AM
#19
Senior Member
Join Date: Oct 2010
Location: upper part of Michigan
Posts: 310
Thanks for this help...........I can't get mine to be 12 1/2 either........
:oops: :oops:
Originally Posted by feline fanatic
Block it! I have often been able to eke out the 1/4 by blocking. To block your coming up short block this is how I do it. I have a cork bulletin board that I drew my 12 1/2" square on with a permanent sharpy marker using my square 12 1/2" ruler. I pin my block to it first doing opposite corners then the sides matching up the edges of my block to my marked outline on the bulletin board. You need to stretch it a bit but usually this is not a problem and I use a lot of pins to do this. Then take a spray bottle with water and spritz the pinned block until it is thoroughly saturated. Walk away and let it air dry overnight. When you unpin it it will retain the squared size of 12 1/2".
Thread
Thread Starter
Forum
Replies
Last Post
