log cabin for quilt backing
#1
log cabin for quilt backing
I have two sampler quilts made out of Christmas fabric and have been trying to decide what I want to do for the backing. Today I saw a quilt that had a log cabin back, just one large block, and thought that would be fun. Here's my question...my quilts are rectangles so how to I figure out the sizes to cut the logs? I have never done a log cabin but understand how. I need to see what the quilts measure, have it written down, but am not sure exactly how to go about this.
Thanks!
Thanks!
#2
To make a rectangular log cabin, you just need to make your central "square" a rectangle, similar to this cushion I made for our deacon's bench:
[ATTACH=CONFIG]575945[/ATTACH]
I think I would figure out the width/length ratio of the size quilt back, and use that same ratio for the central piece, and then divide the remainder by the number of logs I wanted to add.
Daffy
[ATTACH=CONFIG]575945[/ATTACH]
I think I would figure out the width/length ratio of the size quilt back, and use that same ratio for the central piece, and then divide the remainder by the number of logs I wanted to add.
Daffy
#3
If you want to make one large block to cover the whole back you will end
up short for the length of your quilt. Put it on graph paper then add
another piece of fabric or some smaller log cabins to complete the back.
Bear in mind that anything you put on the edge might get cut off when
you trim your quilt (that is, if you do).
up short for the length of your quilt. Put it on graph paper then add
another piece of fabric or some smaller log cabins to complete the back.
Bear in mind that anything you put on the edge might get cut off when
you trim your quilt (that is, if you do).
#5
Super Member
Join Date: Jul 2012
Location: Morris Plains, NJ
Posts: 1,802
What will the dimensions of your finished quilt top be? Are they divisible by an even number in both length and width? E.g. If finished top dimensions are 55 x 66, it is divisible by 11 and 5 1/2" and 2 3/4". I would graph using the 5 1/2" logs (then add the 1/2" seam allowance) because I think you sounded like you wanted a big graphic statement and one block. Maybe I read you wrong. Sounds like a fun back.
#6
Power Poster
Join Date: Jul 2008
Location: East Oklahoma - pining for Massachusetts
Posts: 10,477
You have just given me an idea. I do not have a whole lot of any one thing for backing and very often piece them. I am thinking that I could do some large block and make the back more interesting, plus not go buy more of what I am trying to use up. Thanks.
#7
Super Member
Join Date: Aug 2011
Location: kansas
Posts: 6,407
if you are having this quilted by a long arm quilter, remember that you'll need to add about 4-6" on each side and that when rolled, it will not line up exactly, so your logs may end up slimmer on the one end.
#9
Maureen, you read correctly big and graphic one block. I need to remeasure the tops because I wrote it down somewhere that I would be sure to find again...
Not sending these to the LA, will have to do it myself.
So, I will post back when I get measurements and see what I come up with.
Thanks.
Not sending these to the LA, will have to do it myself.
So, I will post back when I get measurements and see what I come up with.
Thanks.
#10
Power Poster
Join Date: May 2008
Location: MN
Posts: 24,420
It is difficult to line up a back exactly with a top - so you might want to consider some sort of design factor to give yourself some wiggle room.
What size are your tops?
What about doing Courthouse Steps - that way you could have the same colors on top and bottom?
If I was going to draft a pattern - I would start with the "finished size" - and start adding strips from the outside edges to the center - and then whatever I had "left over in the middle" - would be the size of the center/middle rectangle (plus seam allowances) - and then add "extra" to the outside pieces to allow for a bit of shifting -
What size are your tops?
What about doing Courthouse Steps - that way you could have the same colors on top and bottom?
If I was going to draft a pattern - I would start with the "finished size" - and start adding strips from the outside edges to the center - and then whatever I had "left over in the middle" - would be the size of the center/middle rectangle (plus seam allowances) - and then add "extra" to the outside pieces to allow for a bit of shifting -
Thread
Thread Starter
Forum
Replies
Last Post
AngelinaMaria
Main
7
02-13-2013 07:49 AM