My least favorite thing.....
#11
I use a very large basting stitch by hand. Takes about 45 mins to an hour to baste a queen size quilt, never had a problem with movement either. I start with a + basting line then a X and baste in between these markings...easy and easier to remove!!
#12
Originally Posted by katier825
I hate pins! Love the spray baste. If you haven't tried it, give it a shot. You may never go back to pins. :)
#15
Super Member
Join Date: Aug 2010
Location: Jacksonville NC
Posts: 6,510
Originally Posted by nativetexan
Kwik Klip is the tool and JoAnn's has them.
you can actually use a grapefruit spoon if necessary. the "teeth" on the edge work well on holding the pin until you close it.
you can actually use a grapefruit spoon if necessary. the "teeth" on the edge work well on holding the pin until you close it.
#17
I use the Quik Clip for basting with a fabric tagging gun. I put the needle in, pick up 1/8" of the backing and come back up through the top, slide the Quik Clip under the needle and pull the trigger. Takes a lot longer to describe it than to do it. :)
I use the 1/4" long barbs and the gun/barbs made for fine fabrics and I can baste a queen size quilt in about 15 or 20 minutes - about 2 hours less than it takes with pins.
I LOVE fusible batts - you don't have to use pins or barbs at all, but I still use some, just to keep the strain off of the glue bond. The fusible glue washes out after a couple of launderings and the quilt is soft and drape-y.
The fusible batts are especially good when you have bought a quilt top that isn't well pieced or hasn't been properly pressed during its assembly.
With a steam iron and fusible batting, you can just about beat those "bad quilts" into submission. Costs a few bucks more, but worth it for the lessened frustration factor. :)
I use the 1/4" long barbs and the gun/barbs made for fine fabrics and I can baste a queen size quilt in about 15 or 20 minutes - about 2 hours less than it takes with pins.
I LOVE fusible batts - you don't have to use pins or barbs at all, but I still use some, just to keep the strain off of the glue bond. The fusible glue washes out after a couple of launderings and the quilt is soft and drape-y.
The fusible batts are especially good when you have bought a quilt top that isn't well pieced or hasn't been properly pressed during its assembly.
With a steam iron and fusible batting, you can just about beat those "bad quilts" into submission. Costs a few bucks more, but worth it for the lessened frustration factor. :)
#18
Originally Posted by davidwent
As a newbie, of course everything on my quilt is new. I am now basting the quilt with those *insert expletive here* pins!!! I hate it Especially with my fat fingers!
I saw a tute when I first joined this board on you tube and this lady had a tool that looked like a wooden screwdriver, but instead of a blade on the end it had grooves that when she pushed the pins through caught a groove and she closed it right up. I didn't think much of it at the time but would I love one now!!
Yes I am working on my quilt on Christmas...told ya I am hooked! LOL
David
I saw a tute when I first joined this board on you tube and this lady had a tool that looked like a wooden screwdriver, but instead of a blade on the end it had grooves that when she pushed the pins through caught a groove and she closed it right up. I didn't think much of it at the time but would I love one now!!
Yes I am working on my quilt on Christmas...told ya I am hooked! LOL
David
#19
Originally Posted by JoAnnGC
Originally Posted by katier825
I hate pins! Love the spray baste. If you haven't tried it, give it a shot. You may never go back to pins. :)
Thread
Thread Starter
Forum
Replies
Last Post
DebQuilter50
Main
72
01-18-2021 07:22 AM