"Design wall"
#31
Super Member
Join Date: Apr 2011
Location: Ohio
Posts: 2,077
1) cover a piece of poplar in batting or fleece and just lean it against the wall (I use the full sheet, which is the size of a piece of drywall) just used a staple gun to put the batting on OR
2) Use one of those vinyl tablecloths....they have the fuzzy stuff on the back. You can either leave it hanging on the wall, or roll it up in between sewing sessions. Voila!
2) Use one of those vinyl tablecloths....they have the fuzzy stuff on the back. You can either leave it hanging on the wall, or roll it up in between sewing sessions. Voila!
#32
Super Member
Join Date: Nov 2009
Location: S C michigan
Posts: 2,118
i used an 8 ft wooden dowel used for closet rods. hung it from the basement ceiling with a sheet strung on it. works fine in my basement. have to pin the blocks or quilt to it. see my DJ quilt done. ...
#33
Super Member
Join Date: Oct 2009
Location: Maine-ly Florida
Posts: 3,926
My design wall is a heavy weight flannel sheet (from the Vermont Country Store catalog...a little pricey but more heavyweight than I could find elsewhere) hanging on clip rings from a decorative curtain rod. I can pin blocks to it if they don't have enough cling or get too big. I also use it to hang up a finished quilt to take pictures. And just for display sometimes. I love seeing blocks on the wall.
If you go the curtain rod route, a couple of words of advice:
Get double the number of clip rings and space them closer together than you would for a curtain. Provides more support and the flannel sheet won't ripple as much.
My flannel sheet rippled more than I wanted so I sewed a 4-inch wide band of curtain header (the polyester type, not the heavier buckram) to the top. That eliminated the ripples.
Anita
If you go the curtain rod route, a couple of words of advice:
Get double the number of clip rings and space them closer together than you would for a curtain. Provides more support and the flannel sheet won't ripple as much.
My flannel sheet rippled more than I wanted so I sewed a 4-inch wide band of curtain header (the polyester type, not the heavier buckram) to the top. That eliminated the ripples.
Anita
I've been thinking of doing this too. Did you use the two hangers that come with the curtain rod to hang your design wall? If you did, did the design wall hang out from the wall? I wasn't sure how to tackle this.
Thanks,
lots2do
#35
Member
Join Date: Aug 2011
Posts: 37
I got a 4 x 8 insulated wall board( not sure exactly what it's called ) at Lowe's .. I think it's for putting under vinyl siding. There is different thicknesses, I got the 2 inch, then I covered it with headliner. It's the stuff that is used for the ceiling inside your car. I got this at Hancock Fabrics in Louisville,KY I'm sure other fabric stores have this. It works better than felt or fleece, I love it
#38
#40
Senior Member
Join Date: Jan 2011
Location: Glen Burnie, MD
Posts: 927
My husband bought me 2 large sheets of wall insulation. I taped them together and it doubles as my design wall and I use it to spray baste my quilt layers. It works great. Large enough to hang a king size quilt for spray basting. It leans against the wall behind my cutting table ready to use whenever I need it. I love it!
Thread
Thread Starter
Forum
Replies
Last Post
bearisgray
General Chit-Chat (non-quilting talk)
65
02-01-2024 09:04 AM
pastimesquiltdesign
Pictures
141
02-01-2012 01:57 PM
pastimesquiltdesign
Pictures
17
01-15-2012 03:04 PM
craftybear
Links and Resources
6
08-22-2011 05:12 PM
craftybear
Main
35
05-20-2011 01:45 PM