Repairing my Pfaff 1222 Log
#11
Member
Thread Starter
Join Date: Nov 2019
Posts: 6
so onto more repair. Well after tinkering and checking out every type of solution. I may have to give up and take it to somebody who have service many pfaff
Still no straight stitch. Feed dogs still feeding way too slow. Just lucky that there are no broken parts. As usualy with german engineering, over engineer the simplest mechanism in life.
[ATTACH=CONFIG]619677[/ATTACH]
[ATTACH=CONFIG]619678[/ATTACH]
[ATTACH=CONFIG]619679[/ATTACH]
[ATTACH=CONFIG]619680[/ATTACH]
I did put everything together if in case I just give it to a repairman.
#12
Member
Join Date: Dec 2020
Posts: 3
log #1
I was finally get to repair the knob dials. see below by unscrewing the lock mechanism
Attachment 619196
More pictures
Attachment 619197
I then fixed on the feed dogs but I think i got it repair but will testing needs to be done. Manual says go to go see the bottom
Attachment 619198
Attachment 619199
Still no straight stitch
Will continue the next time.
I was finally get to repair the knob dials. see below by unscrewing the lock mechanism
Attachment 619196
More pictures
Attachment 619197
I then fixed on the feed dogs but I think i got it repair but will testing needs to be done. Manual says go to go see the bottom
Attachment 619198
Attachment 619199
Still no straight stitch
Will continue the next time.
#13
Member
Join Date: Dec 2020
Posts: 3
Had some free time to look into it today and figured it out. There was a hidden set screw on the needle position gear. Once you remove that, the knob pulls out. Then the bushing and the rest of the stitch length selector dial can be removed.
What causes the bushing to spin is from oil. The bushing is press fit into the housing and should not be lubricated but if it's oiled then oil will work its way in between the housing and bushing, causing the bushing to spin, which causes the white dot/square to move.
I've been reading that the fix is to drill into the housing and install a set screw to permanently hold the bushing in place. I didn't want metal shavings falling down inside near the motor so I just ended up using Red Loctite on the outside of the bushing which is just as good of a fix IMO. Just make sure to remove any oil residue on the bushing and housing with acetone or isopropyl alcohol before applying it. Once cured, it aint coming off unless you stick a torch to it. Make sure the notch at the end of the bushing is perfectly vertical before you press/tap it in because it bonds quickly. I messed up the first time and had to really crank on it with vice grips to remove it.
This was a fairly easy fix. I was expecting to take the entire machine apart based on the several people mentioning that this was a "huge job" but it took me maybe 30 minutes. And this fix will also work hook bushings that seizes onto the shaft and spins inside the housings.
What causes the bushing to spin is from oil. The bushing is press fit into the housing and should not be lubricated but if it's oiled then oil will work its way in between the housing and bushing, causing the bushing to spin, which causes the white dot/square to move.
I've been reading that the fix is to drill into the housing and install a set screw to permanently hold the bushing in place. I didn't want metal shavings falling down inside near the motor so I just ended up using Red Loctite on the outside of the bushing which is just as good of a fix IMO. Just make sure to remove any oil residue on the bushing and housing with acetone or isopropyl alcohol before applying it. Once cured, it aint coming off unless you stick a torch to it. Make sure the notch at the end of the bushing is perfectly vertical before you press/tap it in because it bonds quickly. I messed up the first time and had to really crank on it with vice grips to remove it.
This was a fairly easy fix. I was expecting to take the entire machine apart based on the several people mentioning that this was a "huge job" but it took me maybe 30 minutes. And this fix will also work hook bushings that seizes onto the shaft and spins inside the housings.
#14
Senior Member
Join Date: Jan 2011
Location: Richmond, VA
Posts: 601
#15
Senior Member
Join Date: Jan 2011
Location: Richmond, VA
Posts: 601
My 1222, purchased new in 1975, was supposed to be kaput a few years ago, but I found a technician who got it apart and said there was nothing wrong with it but 40+ years of gunk. He said he used a product you would use to free up gears in a car, or something like that. Anyway, good as new! And they said it was one of the best old workhorse machines made.
#17
Member
Join Date: Mar 2020
Posts: 3
My 1222, purchased new in 1975, was supposed to be kaput a few years ago, but I found a technician who got it apart and said there was nothing wrong with it but 40+ years of gunk. He said he used a product you would use to free up gears in a car, or something like that. Anyway, good as new! And they said it was one of the best old workhorse machines made.
#18
Member
Join Date: Nov 2019
Posts: 1
Had some free time to look into it today and figured it out. There was a hidden set screw on the needle position gear. Once you remove that, the knob pulls out. Then the bushing and the rest of the stitch length selector dial can be removed.
What causes the bushing to spin is from oil. The bushing is press fit into the housing and should not be lubricated but if it's oiled then oil will work its way in between the housing and bushing, causing the bushing to spin, which causes the white dot/square to move.
I've been reading that the fix is to drill into the housing and install a set screw to permanently hold the bushing in place. I didn't want metal shavings falling down inside near the motor so I just ended up using Red Loctite on the outside of the bushing which is just as good of a fix IMO. Just make sure to remove any oil residue on the bushing and housing with acetone or isopropyl alcohol before applying it. Once cured, it aint coming off unless you stick a torch to it. Make sure the notch at the end of the bushing is perfectly vertical before you press/tap it in because it bonds quickly. I messed up the first time and had to really crank on it with vice grips to remove it.
This was a fairly easy fix. I was expecting to take the entire machine apart based on the several people mentioning that this was a "huge job" but it took me maybe 30 minutes. And this fix will also work hook bushings that seizes onto the shaft and spins inside the housings.
What causes the bushing to spin is from oil. The bushing is press fit into the housing and should not be lubricated but if it's oiled then oil will work its way in between the housing and bushing, causing the bushing to spin, which causes the white dot/square to move.
I've been reading that the fix is to drill into the housing and install a set screw to permanently hold the bushing in place. I didn't want metal shavings falling down inside near the motor so I just ended up using Red Loctite on the outside of the bushing which is just as good of a fix IMO. Just make sure to remove any oil residue on the bushing and housing with acetone or isopropyl alcohol before applying it. Once cured, it aint coming off unless you stick a torch to it. Make sure the notch at the end of the bushing is perfectly vertical before you press/tap it in because it bonds quickly. I messed up the first time and had to really crank on it with vice grips to remove it.
This was a fairly easy fix. I was expecting to take the entire machine apart based on the several people mentioning that this was a "huge job" but it took me maybe 30 minutes. And this fix will also work hook bushings that seizes onto the shaft and spins inside the housings.
Unfortunately, the needle position cam got slightly misaligned when I removed the knobs & it took me FOREVER to get everything back together.
I am not using Loctite because I don’t want to make it permanent, just in case I messed up something else & have to remove the knobs again. But I was able to clean the knobs & shafts well. Makes sense about oil causing the knob alignment issue because this machine had been way over-oiled.
Thanks again for taking the time to post this! There is not much info on the internet & the service manual could be much better.
#19
Member
Join Date: Nov 2023
Posts: 8
Had some free time to look into it today and figured it out. There was a hidden set screw on the needle position gear. Once you remove that, the knob pulls out. Then the bushing and the rest of the stitch length selector dial can be removed.
What causes the bushing to spin is from oil. The bushing is press fit into the housing and should not be lubricated but if it's oiled then oil will work its way in between the housing and bushing, causing the bushing to spin, which causes the white dot/square to move.
I've been reading that the fix is to drill into the housing and install a set screw to permanently hold the bushing in place. I didn't want metal shavings falling down inside near the motor so I just ended up using Red Loctite on the outside of the bushing which is just as good of a fix IMO. Just make sure to remove any oil residue on the bushing and housing with acetone or isopropyl alcohol before applying it. Once cured, it aint coming off unless you stick a torch to it. Make sure the notch at the end of the bushing is perfectly vertical before you press/tap it in because it bonds quickly. I messed up the first time and had to really crank on it with vice grips to remove it.
This was a fairly easy fix. I was expecting to take the entire machine apart based on the several people mentioning that this was a "huge job" but it took me maybe 30 minutes. And this fix will also work hook bushings that seizes onto the shaft and spins inside the housings.
What causes the bushing to spin is from oil. The bushing is press fit into the housing and should not be lubricated but if it's oiled then oil will work its way in between the housing and bushing, causing the bushing to spin, which causes the white dot/square to move.
I've been reading that the fix is to drill into the housing and install a set screw to permanently hold the bushing in place. I didn't want metal shavings falling down inside near the motor so I just ended up using Red Loctite on the outside of the bushing which is just as good of a fix IMO. Just make sure to remove any oil residue on the bushing and housing with acetone or isopropyl alcohol before applying it. Once cured, it aint coming off unless you stick a torch to it. Make sure the notch at the end of the bushing is perfectly vertical before you press/tap it in because it bonds quickly. I messed up the first time and had to really crank on it with vice grips to remove it.
This was a fairly easy fix. I was expecting to take the entire machine apart based on the several people mentioning that this was a "huge job" but it took me maybe 30 minutes. And this fix will also work hook bushings that seizes onto the shaft and spins inside the housings.
My machine is a 1222e and I had to remove the bell crank and cam stack housing to get to the screw (youtube). Once the housing was removed I took out the set screw and removed the knob. I then removed the portion of the dial with the white square (the portion of the dial moving when it should be stationary). It pulls toward you, just get something behind it. You can then access a snap ring or gently pry the bushing (rod) from the housing. Mine was fairly difficult to pull out but I did so by working a screwdriver around the back of the stitch selector and the body of the machine. It worked for me but idealy id remove the snap ring if doing it again. My bushing was plenty tight in the housing although it was spinning when turning the stitch selector but it was very difficult to turn. My problem was the bushing or rod was completely frozen in the round bushing of the stitch selector. I tapped it out from the back and the rod came out with the snap ring attached. I removed the snap ring. I cleaned the rod and gummed up bushing and reassembled with the selector and snap ring. Their is also a plus shaped spring that sits inside of the selector between the selector and the snap ring. I tapped the rod back into the housing, making sure to lift the little pawls that ride on the nylon section of the selector as one unit. I did use a little silicone spray on the portion of the rod that the selector sit on. I then used the knob to make sure the hole for the screw lined up for proper depth. Make sure to get the orientation correct so the dial with the white square is in the 12 oclock position as it is notched to fit the end of the rod. Install the dial with the square and then the knob and secure the screw.
Now it turns super smooth and the white dot stays where it is supposed to be.
I hope this post helps someone like nw693's post helped me. Not much good info out there on how to correct this. Everyone was saying to pay someone because it was too difficult or that it was now a parts machine. Nothing was broken or damaged in the machine and just needed to be disassembled, cleaned and reassembled. I didnt even have to use locktite or install a set screw on mine. I had more trouble removing and installing the bell crank and cam stack housing that fixing the stitch selector. Probably took me a bit over an hour for the whole thing taking my time.
Thread
Thread Starter
Forum
Replies
Last Post
jenibeni
For Vintage & Antique Machine Enthusiasts
22
11-27-2016 06:05 PM
Mitch's mom
For Vintage & Antique Machine Enthusiasts
21
02-04-2013 06:50 AM