Question about trimming before adding binding
#1
Super Member
Thread Starter
Join Date: May 2010
Location: Southeast Idaho
Posts: 3,210
I was just wondering if I have been doing this wrong since I am sort of a self-taught quilter. When I am ready to add the binding on my quilt, I always trim the edges, including the batting and backing so I have a straight edge to sew the binding onto. Is this the best way to do this or do you leave it all on so you have some extra batting to add to the binding part to make it not be flat? I am open for suggestions and your reasoning. :-)
#3
Super Member
Join Date: Jun 2011
Location: Michigan. . .FINALLY!!!!
Posts: 6,726
You should leave at least a 1/4" of the batting sticking out from the top. This will help "stuff" the binding and make it firmer. Judges at quilt shows will look for a nice stuffed binding. Plus, if you don't have have your binding stuffed, it will fold in half and then it will start to wear along the edge and split, especially if it is washed a lot. Many antique quilts have split bindings just because they didn't fill the binding enough and they were used and washed a lot.
#5
Super Member
Thread Starter
Join Date: May 2010
Location: Southeast Idaho
Posts: 3,210
Originally Posted by auntpiggylpn
You should leave at least a 1/4" of the batting sticking out from the top. This will help "stuff" the binding and make it firmer. Judges at quilt shows will look for a nice stuffed binding. Plus, if you don't have have your binding stuffed, it will fold in half and then it will start to wear along the edge and split, especially if it is washed a lot. Many antique quilts have split bindings just because they didn't fill the binding enough and they were used and washed a lot.
#6
I do the same.
I do a basting stitch where I think the future seam allowance is going to be. Then I lay the quilt on the floor with my biggest mat underneath and cut the excess away. I am able to double check the straightness against the parquet flooring by lining up my long ruler with the squares. I move around the whole quilt this way - makes the corners square. If I cut off some of my basting I pin that portion to hold the sandwich together. Then I sew my binding on.
Every time I do a large quilt this way I swear I'll never to it again. Never crawl on the floor again. Never, never, never. I don't listen to myself. When I finally manage to get up I head to the medicine cabinet for pain relief and die the rest of the day. :)
I do a basting stitch where I think the future seam allowance is going to be. Then I lay the quilt on the floor with my biggest mat underneath and cut the excess away. I am able to double check the straightness against the parquet flooring by lining up my long ruler with the squares. I move around the whole quilt this way - makes the corners square. If I cut off some of my basting I pin that portion to hold the sandwich together. Then I sew my binding on.
Every time I do a large quilt this way I swear I'll never to it again. Never crawl on the floor again. Never, never, never. I don't listen to myself. When I finally manage to get up I head to the medicine cabinet for pain relief and die the rest of the day. :)
#7
Banned
Join Date: Nov 2010
Posts: 4,134
Originally Posted by SandyinZ4
Originally Posted by auntpiggylpn
You should leave at least a 1/4" of the batting sticking out from the top. This will help "stuff" the binding and make it firmer. Judges at quilt shows will look for a nice stuffed binding. Plus, if you don't have have your binding stuffed, it will fold in half and then it will start to wear along the edge and split, especially if it is washed a lot. Many antique quilts have split bindings just because they didn't fill the binding enough and they were used and washed a lot.
I always trim the top/batting/backing even and then attach the binding.
Here are Sharon Schambers video on binding (there are 3 parts):
http://www.youtube.com/watch?v=4PE0Yq9iGlc
http://www.youtube.com/watch?v=u3vHI7rgZpw
http://www.youtube.com/watch?v=W--xgi4nux8
Makes GORGEOUS, stuffed, firm bindings.
#8
Power Poster
Join Date: Nov 2009
Location: Mableton, GA
Posts: 11,329
I trim mine and square up as much as possible if needed and then sew on the binding. I use a generous 1/4 inch seam with a 2 1/4 or 2 1/2" binding, folded over, and the binding is usually "full". I watched an Eleanor Burns show once where she marked the sides of the quilt and then sewed the binding on and then trimmed off the excess quilt. I tried it once and couldn't make it work for me.
#9
Banned
Join Date: Nov 2010
Posts: 4,134
Originally Posted by Stitchnripper
I tried it once and couldn't make it work for me.
I know many people successfully use this method but I know for sure I'd slice right through whatever I wasn't supposed to cut. :mrgreen:
#10
Banned
Join Date: Dec 2009
Location: Enid, OK
Posts: 8,273
Originally Posted by MTS
Originally Posted by SandyinZ4
Originally Posted by auntpiggylpn
You should leave at least a 1/4" of the batting sticking out from the top. This will help "stuff" the binding and make it firmer. Judges at quilt shows will look for a nice stuffed binding. Plus, if you don't have have your binding stuffed, it will fold in half and then it will start to wear along the edge and split, especially if it is washed a lot. Many antique quilts have split bindings just because they didn't fill the binding enough and they were used and washed a lot.
I always trim the top/batting/backing even and then attach the binding.
Here are Sharon Schambers video on binding (there are 3 parts):
http://www.youtube.com/watch?v=4PE0Yq9iGlc
http://www.youtube.com/watch?v=u3vHI7rgZpw
http://www.youtube.com/watch?v=W--xgi4nux8
Makes GORGEOUS, stuffed, firm bindings.
Thread
Thread Starter
Forum
Replies
Last Post
craftybear
Links and Resources
3
12-25-2010 09:49 PM