wild winding
#1
what kind of machine do you have and do you have spare bobbins? are you able to use any bobbins? I have a Kenmore 150 and the metal bobbins I bought for it are bouncing when I wind them. Anyone else have this kind of problem?
#3
Moderator
Join Date: Jun 2008
Location: Camarillo, California
Posts: 35,242
I have a Bernina 630 and I buy Bernina bobbins. I like having lots of bobbins just ready to go so I have at least 40 bobbins and I wind most of them up with ecru or light grey. When I am ready to quilt a quilt I will wind at least 3 or 4 with thread to match the back. Sometimes the spool of thread spins a lot as I wind and that makes noise. Even JoAnns carries bobbins for different makes, I bought 3 pkgs with a 50% off notions sale. 4 came with my machine and I bought 4 more from my dealer and then bought a batch of 15 or 20 on e-bay
#4
I have a Bernina 200 and a 440QE. They just happen to use different size bobbins :evil: Just make sure the bobbins you're using are the correct ones for that machine. Also, your bobbin probably winds faster than you sew, so it could bounce the machine a little. You can put that rubberized shelf liner underneath. My 200 is the one I use for embroidery and without the shelf liner stuff, it sounds and looks like it's going to bounce off the table... :wink:
#5
Moderator
Join Date: Jan 2007
Location: In the middle of a mess...
Posts: 20,027
I only use the plastic bobbins that are made for my Kenmore. I've tried the metal ones that say they CAN be used with Kenmore, but, like yours, they bounce. So I fixed that problem....I tossed them all out.
#6
Originally Posted by tlrnhi
I only use the plastic bobbins that are made for my Kenmore. I've tried the metal ones that say they CAN be used with Kenmore, but, like yours, they bounce. So I fixed that problem....I tossed them all out.
#7
Power Poster
Join Date: May 2008
Location: MN
Posts: 24,659
The lady at the sewing machine place told me that the repair place calibrates the machine for either a plastic or metal bobbin.
I've used both metal and plastic bobbins with my Pfaff (mid 1980's ) and the old Singers (1960s) and they seem to work okay to me.
I also like to have LOTS of bobbins on hand. Can't waste that last 20 feet of thread on that bobbin, now, can we.
I've used both metal and plastic bobbins with my Pfaff (mid 1980's ) and the old Singers (1960s) and they seem to work okay to me.
I also like to have LOTS of bobbins on hand. Can't waste that last 20 feet of thread on that bobbin, now, can we.
#8
Moderator
Join Date: Jan 2007
Location: In the middle of a mess...
Posts: 20,027
Originally Posted by DA Mayer
Originally Posted by tlrnhi
I only use the plastic bobbins that are made for my Kenmore. I've tried the metal ones that say they CAN be used with Kenmore, but, like yours, they bounce. So I fixed that problem....I tossed them all out.
#9
Moderator
Join Date: Jun 2008
Location: Camarillo, California
Posts: 35,242
It's funny, I hate wasting thread so I will either throw in my almost empty bobbins when I am piecing small items or sometime I will just use it on the top where I can keep an eye on it. I never start quilting with a partial bobbin. Always a full one, hate to run out while quilting!!!!
#10
I have 2 Kenmores and a Brother and found that Class 15 metal or plastic will work on all of them. The only bounce I have had was because the bobbin was not snapped in completely and left too much wiggle room.
Thread
Thread Starter
Forum
Replies
Last Post