Singer 201-3 "The Aristocrat of Sewing Machines"
#11
Super Member
Join Date: Sep 2012
Location: Homosassa, FL
Posts: 2,267
Have my grandmothers 201-3 that was bought in Sherbrooke, Que. Canada in the early 50's. I is in a wood casen not a cabinet but still sews great and looks great. I have had it for years, and before that my mother used it.
#14
OH, NFl quilter you did good. A 201 in that condition is on my bucket list but did not know they compare to a 66.
That stretch look is what interests me. What is distance in harp ? Never did hear back about that other set.
That stretch look is what interests me. What is distance in harp ? Never did hear back about that other set.
#16
Super Member
Join Date: Feb 2012
Posts: 8,091
NL Quilter,
That is a very nice machine. I wouldn't mind adding one to my hoard .... 'er, stash .... oh, collection. That's what it is.
But it's not a Centennially badged machine.
This is a Centennial Badge:
[ATTACH=CONFIG]421189[/ATTACH]
At least it is on USA made 201-2s and other Centennials I've seen.
Speaking of which here is mine. Please forgive the mess around it.
[ATTACH=CONFIG]421190[/ATTACH]
And the cabinet:
[ATTACH=CONFIG]421191[/ATTACH]
Mine is also a knee controlled machine. It works really good. I find the knee controllers to be somewhat less fatiguing than the foot controller sometimes.
Joe
That is a very nice machine. I wouldn't mind adding one to my hoard .... 'er, stash .... oh, collection. That's what it is.
But it's not a Centennially badged machine.
This is a Centennial Badge:
[ATTACH=CONFIG]421189[/ATTACH]
At least it is on USA made 201-2s and other Centennials I've seen.
Speaking of which here is mine. Please forgive the mess around it.
[ATTACH=CONFIG]421190[/ATTACH]
And the cabinet:
[ATTACH=CONFIG]421191[/ATTACH]
Mine is also a knee controlled machine. It works really good. I find the knee controllers to be somewhat less fatiguing than the foot controller sometimes.
Joe
#17
Junior Member
Thread Starter
Join Date: Apr 2013
Location: St. John's NL Canada
Posts: 110
Thanks for the clarification Joe, according to the serial # it was produced in 1951, but not badged. As well an interesting note, according to the serial # it is a 201k indicating it was manufactured in Scotland. When I cleaning it, and taking all the small parts off to clean such as the little wheel used to direct the bobbin thread onto the bobbin when whinding it is stamped made in Canada.
#18
Super Member
Join Date: Feb 2012
Posts: 8,091
I have seen Singers that were made in 1950 that are Centennially marked so they could have stock on hand for early 1951. Perhaps those made in 51 that are not badged as a Centennial were made late in the year for the next years market. I really don't know.
I have some of the Canadian made parts in my machines too. Not sure why they intermixed the nations of manufacture but it happens. The motors I understand. UK uses 220 or 240 Volt motors, ( not sure which ) so they just sent the machines over and the country of destination supplied the motor.
Joe
I have some of the Canadian made parts in my machines too. Not sure why they intermixed the nations of manufacture but it happens. The motors I understand. UK uses 220 or 240 Volt motors, ( not sure which ) so they just sent the machines over and the country of destination supplied the motor.
Joe
#19
UK uses 230V, Australia uses 240V. Supply voltages are never exactly what they're supposed to be and vary about 10-15 volts (go on, get a volt meter and test it). The UK and AU voltages are so close that the same motor works interchangeably and Singer motors from both Scotland and Australia are usually marked "230-250 volts" (yes I did just look).
Mike
Mike
Thread
Thread Starter
Forum
Replies
Last Post
bearisgray
General Chit-Chat (non-quilting talk)
65
02-01-2024 09:04 AM
miriam
For Vintage & Antique Machine Enthusiasts
154
03-12-2014 07:43 AM
flawhoopi
For Vintage & Antique Machine Enthusiasts
6
12-22-2013 11:29 PM
Carol34446
For Vintage & Antique Machine Enthusiasts
1
09-16-2013 10:53 AM
SingerSewer
Main
10
06-22-2013 06:24 AM