Best Way to Add Borders to Quilts
#1
Super Member
Thread Starter
Join Date: Nov 2010
Location: Cincinnati, OH
Posts: 4,016
Best Way to Add Borders to Quilts
When I add a border to a quilt, I just cut a strip of fabric longer than the quilt, sew it to the quilt and then cut off the excess. I know many people measure the quilt in a couple different places, take the average, and cut the border to that specification. Does it matter which way you do it? Is one a better method? (I don't want to say right or wrong!) Would love advice on which method produces a better quilt. Thanks
#2
If you just cut sew then trim you will risk having wavy borders, possibly bad enough they will need re-done before quilting. The best practice (not the quilt police, just saying IMHO) is to measure the top, middle and bottom. Then average that to get the length for side borders. then after those borders are on, measure the left, middle then right side. Average this and you will have your top and bottom borders. (You can do top or sides first your choice). I also round down to the nearest 1/8th inch instead of up. I have never had a wavy border doing it this way. When I first started, I didn't know about this process, and had to redo a couple quilts because I would have had to pleat the borders to make them fit. Wouldn't have been the most pleasing look.
Last edited by knlsmith; 04-09-2013 at 07:41 AM. Reason: addtional info
#4
Senior Member
Join Date: Dec 2012
Posts: 538
Either I've been lucky and haven't had wavy results, or I don't know what, but I, too, just measure up the side, and across the (top or bottom) and multiply by 2. I've never really understood about measuring the center of vertical & horizontal; what if your quilt is skewed and it's got a swag in the middle and your measurement is now too short?
Would love to finally understand this.
Would love to finally understand this.
#5
I don't know the math or reason why it works, it just does. I will say that my measurements are never more than an 1/8 in difference. I have OCD and sew very squarely. LOL It's a good thing in this respect to be that way I suppose. I bet someone will chime in with a great explanation.
Either I've been lucky and haven't had wavy results, or I don't know what, but I, too, just measure up the side, and across the (top or bottom) and multiply by 2. I've never really understood about measuring the center of vertical & horizontal; what if your quilt is skewed and it's got a swag in the middle and your measurement is now too short?
Would love to finally understand this.
Would love to finally understand this.
#7
Senior Member
Join Date: Jan 2012
Location: Texas
Posts: 512
I used to do it that way, too, until I had waves the size of a Tsunami on one of my quilts. Never again. I measure thru the middle lengthwise and crosswise and use those measurements to cut my borders, then, pin in case I have to ease it in. Works for me.
#8
it helps to to square up your quilt in case it is a bit too long/short on one side or the middle, I cut mine long and mark where it should end, sometimes I still have to fudge a dab one way or the other. after I'm sure it's good then I cut it off
__________________
http://www.etsy.com/shop/kathykwilts?ref=ss_profile
http://www.etsy.com/shop/kathykwilts?ref=ss_profile
#9
I have found the key to being able to sewing and trimming them to length is sewing with the border fabric on top of the quilt. If you sew with the border fabric next to the feed dogs it eases it in slightly and causes wavy borders.
#10
Super Member
Join Date: Jul 2011
Location: Rhode Island
Posts: 2,301
I measure the center of my quilt both ways,That gives you a more true measurement. One side of your quilt might not be the same on both sides. If you measure the center that gives you a truer measurement.
Thread
Thread Starter
Forum
Replies
Last Post
copycat
Main
9
04-13-2016 11:51 AM
oklahomamom2
Main
10
02-21-2015 10:43 AM
Trisher
Main
73
01-13-2014 08:43 AM